English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 145 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author First layer inconsistencies and outer wall sep... Przez mparker2531 on Sep 11, 19 1807 3 mparker2531 What alignment is good enough? Przez -- on Sep 11, 19 2048 4 Emil First layer problem Przez -- on Sep 11, 19 1723 3 Miiamin Small prints stop sticking Przez rawfire on Sep 11, 19 3160 6 rawfire Clean Up Parts Przez McLaren Wang on Sep 11, 19 1603 1 McLaren Wang Certain Screw Tighteness Przez McLaren Wang on Sep 11, 19 1328 1 McLaren Wang just assembled, applied power, but nothing - n... Przez rmm200 on Sep 10, 19 1617 2 Greg Best disassembly route for MK3S to check hot e... Przez Ben Park on Sep 09, 19 2080 2 bobof First Layer Issues Answered Przez bobstro on Sep 09, 19 2598 4 Bobby First print help needed Answered Przez Kasem427 on Sep 08, 19 1987 3 Kasem427 First layer issues / bed level correction feat... Przez -- on Sep 08, 19 3193 9 bobof Stringing with Prusa PET and i3 MK3 Przez Bunny Science on Sep 08, 19 2316 4 Andreas Test print doesn't start properly Przez -- on Sep 08, 19 1855 2 neekburm Need Help Przez -- on Sep 08, 19 1471 4 Sandi Thermistor issue? Przez Brad on Sep 07, 19 2074 3 Brad Line pattern on heat sheet Przez Kevlar on Sep 07, 19 1597 4 Kevlar How's My Benchy Look? Przez Adam on Sep 06, 19 3026 7 Adam printer fails to print from sd card Przez -- on Sep 05, 19 1589 2 sitterlet Z Axis Calibration - Problems Przez -- on Sep 05, 19 18735 18 Yngeinstn Soliciting suggestions for improvement on my f... Przez -- on Sep 05, 19 1823 8 timyoungenato... Strona 145 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: