English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 135 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Missing parts for MK3S build at #7, Heatbed an... Von Olef on Dec 18, 19 1916 3 AL Dev New MK3S - Staircasing/Y Axis Issue Von shad0wth3fall3... on Dec 18, 19 2644 4 shad0wth3fall... [Build Problems] E-Exis FS-Cover Assembly Issu... Von rmm200 on Dec 17, 19 2950 9 CAR Extruder clicking and not feeding Von Mr Disintegrat... on Dec 17, 19 2456 4 Mr Disintegra... Possible Y-Axis belt tightening under spec Von crazycabo350 on Dec 17, 19 1894 3 crazycabo350 Consistent Filament Excrusion Von fwcox on Dec 16, 19 1778 2 fwcox Jam, then black ring was pulled out!? Von millner.ryan on Dec 16, 19 2206 4 millner.ryan Filament not catching/loading Von Ken G. on Dec 15, 19 1847 2 Squizzie First Print Issues Von Ken G. on Dec 14, 19 2096 7 RB Thanks for advice managed to print this. Von Ken G. on Dec 14, 19 1558 4 VFXWELFY Printer stuck in a corner Answered Von Nicolas on Dec 14, 19 2274 3 Nicolas LCD not working on newly built MK3S Von JoanTabb on Dec 13, 19 2538 10 Blake metal print sheet not sticking to print bed. M... Von rmm200 on Dec 13, 19 2441 3 skrok Issue with first test Print, error message ple... Von guyennon.sophi... on Dec 11, 19 2055 5 duval105 what went wrong here? bridge issues with ASA Von hawai on Dec 11, 19 2080 2 hawai 1st Layer Calibration issues Von JoanTabb on Dec 10, 19 2351 4 Anthony First layer calibration - blob and crunching s... Von rmm200 on Dec 09, 19 1987 2 raoul.d2 Printer do not turn on any more Von rmm200 on Dec 09, 19 2223 8 thomas-4 First layer Z height Answered Von Justin Porteus on Dec 09, 19 3211 10 Justin Porteu... Purchased i3 MK3/S with MMU2S together Von Darron on Dec 05, 19 1914 4 Darron Seite 135 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Teilen: