English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 134 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author First layer looks always horrible in the middl... By friedemann on Dec 28, 19 4374 4 friedemann X axis shift while homing - Odd issue that I c... By cvjrod on Dec 26, 19 4591 12 3dweltan Powder coated bed not working well By cwbullet on Dec 25, 19 1815 4 lembo First layer areas with different heights Answered By JoanTabb on Dec 25, 19 2039 6 CE Built the machine, but when I do the first lay... By Ken G. on Dec 24, 19 9169 30 Ken G. bed temperature regulation problems By JoanTabb on Dec 24, 19 1475 3 cdg3dprinting First layer calibration and Filament ooze Answered By AeroNerd on Dec 24, 19 2653 7 AeroNerd Constant preheat and thermal runaway errors! By PrinterGuy74 on Dec 24, 19 1955 3 PrinterGuy74 possible nozzle clog? By bobstro on Dec 22, 19 1539 2 Andy Y-AXIS CALIBRATION PROBLEM By wbDheartG on Dec 21, 19 4349 3 wbDheartG XYZ Dimensional Error By Mike Daneman on Dec 19, 19 1548 2 michael.h5 Printer not extruding enough filament, results... By simon-2 on Dec 19, 19 4083 8 simon-2 Filament sensor always active By JoanTabb on Dec 18, 19 1765 4 raul Missing parts for MK3S build at #7, Heatbed an... By Olef on Dec 18, 19 1810 3 AL Dev New MK3S - Staircasing/Y Axis Issue By shad0wth3fall3... on Dec 18, 19 2540 4 shad0wth3fall... [Build Problems] E-Exis FS-Cover Assembly Issu... By rmm200 on Dec 17, 19 2799 9 CAR Extruder clicking and not feeding By Mr Disintegrat... on Dec 17, 19 2332 4 Mr Disintegra... Possible Y-Axis belt tightening under spec By crazycabo350 on Dec 17, 19 1801 3 crazycabo350 Consistent Filament Excrusion By fwcox on Dec 16, 19 1684 2 fwcox Jam, then black ring was pulled out!? By millner.ryan on Dec 16, 19 2012 4 millner.ryan Page 134 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: