English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 12 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Calibration Failed! Check the axes and run aga... Answered Przez angkianglong on Sep 15, 23 4872 25 JandLMak3rs XYZ Calibration failed, check axes Przez angkianglong on Sep 15, 23 9425 16 rgordon0 X-Axis Calibration Failed! Przez angkianglong on Sep 15, 23 2747 6 jamie.c5 Right Z axis climbs higher than left Przez holbrookk on Sep 15, 23 1301 6 Gundam Pharma... MK3S No Longer Works after MMU3 Install Przez TC2 on Sep 15, 23 868 4 TC2 Custom first layer calibration gcode on damage... Przez Pascal Heitz on Sep 14, 23 855 3 Pascal Heitz XYZ calibration point not found screen illumin... Przez Ariel M on Sep 14, 23 867 2 Ariel M Shifting Perimeters Przez Void879 on Sep 08, 23 857 5 Void879 Simple question on end of print hot end and be... Answered Przez Hello on Sep 07, 23 812 7 Davebert Crashes detected in Y-Axis without apparent re... Przez mcad2000 on Sep 07, 23 8116 14 Metikumi Calibration failed! Check the axes and run aga... Przez vosslab on Sep 06, 23 2342 6 abdulla.a4 Calibration attempts to drill hole in steel sh... Przez JdL on Sep 04, 23 1253 7 JdL Printer keeps clogging after a few hours Przez TKTech on Sep 03, 23 4664 7 patrick.f18 Yet another yet another extruder grub screw po... Przez wcndave on Sep 03, 23 672 1 wcndave Print bed low in center Przez alex.limtiaco on Aug 29, 23 11444 20 william.e9 Again, first layer Przez lschelvis on Aug 29, 23 1158 6 lschelvis front fan error on self-test Przez Frederiiiic on Aug 27, 23 885 1 Frederiiiic Prints are skipping at a specific Z-height Przez Robin_13 on Aug 27, 23 1212 2 William Pella... Humidity Przez Robin_13 on Aug 27, 23 1090 7 Michael Pieri... Filament IR Sensor reading filament has run ou... Przez Robiscash on Aug 24, 23 858 1 Robiscash Strona 12 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: