English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 11 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Print Fan Error - fan spins, can change rpm fr... Por steve on Dec 20, 23 1534 3 derei First Layer Frustration/Calibration Settings Por steve on Dec 20, 23 1975 7 Kflood Printer will not extrude after putting it in t... Por LackyMan23 on Dec 18, 23 2102 7 LackyMan23 Consistent Benchy Failure Por Conor Schafer on Dec 13, 23 1609 3 Conor Schafer Infill troubles Por LackyMan23 on Dec 11, 23 1378 2 Freddy bed visualize adjustment Por Michael Oakley on Dec 10, 23 1446 1 Michael Oakle... Bad first print Por JoanTabb on Dec 10, 23 1603 4 Eule Sending of broken parts （Under assembly） Por JoanTabb on Dec 09, 23 1265 5 LkbjF5 What kind of Printing Failure is this Answered Por jsw on Dec 05, 23 1319 2 Kim Jones Material Change during printing Answered Por Diem on Dec 05, 23 1430 4 Kim Jones Filament Spool Tangled Por Larswaden on Dec 04, 23 8724 8 patrickho138 After full calibration... Nozzle dig into mode... Por kurt _hectic on Dec 03, 23 2136 8 kurt _hectic Printing fails - unknown issue Answered Por JoanTabb on Nov 30, 23 1697 10 Kim Jones Cannot flatten the heat bed, even with nylocks... Por Diem on Nov 30, 23 1195 5 Fran Perea Calibration/Selftest failure, X Axis Length Por David Kenyon on Nov 30, 23 1409 8 David Kenyon Z-height issue in rear left corner (solved!) Por JRayne on Nov 25, 23 1152 1 JRayne Setting up new-to-me i3 MK3 via Config Wizard Por Hello on Nov 23, 23 2031 2 Vincent L Print Fail - X axis shifted during print Por Neophyl on Nov 17, 23 1474 2 airrj Holes in Print Por Neophyl on Nov 16, 23 1797 9 Manuel Hauser PETG print stuck Por Floyd on Nov 13, 23 1740 6 Floyd Página 11 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: