English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 101 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Layer shifting, trouble with first prints Da pbobbett on Sep 03, 20 2374 13 pbobbett Cannot feed filament: New MK3s Da jsw on Sep 02, 20 2400 6 robroy90 Shifting in X and comming backto origin positi... Da Neophyl on Sep 02, 20 1621 2 Jetfan First Layer Fine....apart from supports Da Neophyl on Sep 02, 20 2986 13 jesterminute Y axis calibration fails Da robotics on Sep 01, 20 1395 3 robotics Adhesion issues and print quality. Da -- on Sep 01, 20 9042 47 01Pad Filament change loop Da Clemens M. on Sep 01, 20 1768 5 raco66 Squeaky sound from extruder during print Da -- on Sep 01, 20 1226 2 David Kennis Wizard and Z-Axis Calibration Fail Da GKMAKEIT on Sep 01, 20 4840 5 james.f31 Prusa MK3S making weird sounds Da David Kennis on Aug 31, 20 2342 3 smoknjoe44 Is this bad benchy due to bad belt tension? Da Peter M on Aug 31, 20 1641 2 smbistrian New build, serious problem Da daedalusminos on Aug 30, 20 1425 1 daedalusminos Edges Deform and Get Caught Da Peter M on Aug 30, 20 2447 6 addison.l Problems after nozzle change Da anricco on Aug 30, 20 16683 10 samuel.zetter... Z axis nightmare >_ Da GKMAKEIT on Aug 30, 20 1632 6 daronofsky Flat surface quality ok or up for improvement? Answered Da Ruud on Aug 28, 20 2198 4 Ruud Help with supports and print quality Da jonathan.s30 on Aug 28, 20 1382 1 jonathan.s30 Stripped out 3d E-Axis part on Original Prusa ... Da tj on Aug 28, 20 1586 2 Gurthang99 Textured plate Da jsw on Aug 28, 20 3437 16 SteveS Too much filament extruded ? First layer fail. Da Neophyl on Aug 28, 20 2378 5 MTom Pagina 101 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: