5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!
 
Benachrichtigungen
Alles löschen

5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!  

Seite 2 / 8
  RSS
Tom_3D
(@tom_3d)
Active Member
RE:

Wow with this news i´m super excited to try ! Prusa teams are best i don´t expected they put new fast IS, PA etc from MK4 !

Thanks a lot ! 

Díky borci!

Veröffentlicht : 19/09/2023 9:22 am
Andy Piper gefällt das
Pitel
(@pitel)
Eminent Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

Please add 0.6 nozzle support to the slicer. 🙏🏻

Veröffentlicht : 19/09/2023 11:33 am
Arash68 und IG gefällt das
Werner-Sellschopp
(@werner-sellschopp)
Active Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

Thankyou for this amazing peace of firmware. Works nearly perfect.

But the Bonkers-Benchy, printed in 18 minutes, had a little bit of underextrusion. The same benchy, printed in 40 minutes with the included settings, had a perfect finish.

Veröffentlicht : 19/09/2023 11:45 am
Werner-Sellschopp
(@werner-sellschopp)
Active Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

PS:

... I think, 40 minutes is fast enough

Veröffentlicht : 19/09/2023 11:51 am
Andy Piper gefällt das
Kaspervm
(@kaspervm)
Mitglied
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

That just happened to me. I sliced the file again and now it is printing. 1. layer going down. 

Could it be the timestamp from installing the firmware / creating the file in the slicer? -i have no idea...

Veröffentlicht : 19/09/2023 12:04 pm
PGe-10
(@pge-10)
Active Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

Now I can't get it in my amateur head, don't I need to connect an extra sensor to be able to run Input Shaper on Mini+ printer???

Veröffentlicht : 19/09/2023 12:44 pm
Tom_3D gefällt das
cwbullet
(@cwbullet)
Mitglied
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

Nope.  

Posted by: @pge

Now I can't get it in my amateur head, don't I need to connect an extra sensor to be able to run Input Shaper on Mini+ printer???

 

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 19/09/2023 1:22 pm
cwbullet
(@cwbullet)
Mitglied
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

For some reason, I cannot get this to install on one of my Minis.  Do I need to change to file name?

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 19/09/2023 1:23 pm
PGe-10
(@pge-10)
Active Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

Have you read this? Can it help?

Firmware update instructions

Make sure you are running firmware 4.4.1, see the release notes for firmware files and instructions. Once the 4.4.1 is installed proceed to flashing the 5.1.0-alpha1 firmware. Note that the upgrade might take longer than usual

Veröffentlicht : 19/09/2023 1:35 pm
horza
(@horza)
Mitglied
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

last line in known bugs section on the release page says:

In rare cases the printer might have issues with homing, a temporary fix is to hold the print head for a while while homing

So that's what I did - while selftesting X, I held the head stuck to the extruder so it can't "bounce" back for 2 seconds. Released it after 2 seconds and it continued testing X axis and everything else just fine.

Veröffentlicht : 19/09/2023 1:37 pm
cwbullet
(@cwbullet)
Mitglied
RE:

Yes, and I have 4.4.1.  Do not assume someone did not read the instructions.  One of my printers is just not acknowledging the firmware file is on the thumb drive.  I have it on one and I guess I will try a third printer instead.  

Posted by: @pge

Have you read this? Can it help?

Firmware update instructions

Make sure you are running firmware 4.4.1, see the release notes for firmware files and instructions. Once the 4.4.1 is installed proceed to flashing the 5.1.0-alpha1 firmware. Note that the upgrade might take longer than usual

 

Diese r Beitrag wurde geändert Vor 1 year von cwbullet

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 19/09/2023 1:41 pm
PGe-10
(@pge-10)
Active Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

 

I'm very sorry, I meant no harm. On the contrary, I wanted to try to help

 
Veröffentlicht : 19/09/2023 1:48 pm
cwbullet
(@cwbullet)
Mitglied
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

I appreciate that.  I am not sure about what is causing it.  One printer worked.  One went into a perpetual boot loop when I tried to update to 4.4.1.  A third would not recognize the input shaper firmware.  I guess that means I will be trying a fourth tonight.  

Posted by: @pge

 

I'm very sorry, I meant no harm. On the contrary, I wanted to try to help

 

 

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 19/09/2023 1:52 pm
SuperJudge
(@superjudge)
Active Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

 

Posted by: @pitel

Please add 0.6 nozzle support to the slicer. 🙏🏻

Whimpers in Bondtech CHT 0.5mm

Mini+: Bondtech extruder, Bondtech throat, Input Shaper firmware -- XL: single toolhead, Bondtech CHT 0.6mm, Input Shaper firmware
Veröffentlicht : 19/09/2023 1:57 pm
timovp
(@timovp)
Mitglied
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

Seconding this. For now, swapped the nozzle and started a first print

Posted by: @pitel

Please add 0.6 nozzle support to the slicer. 🙏🏻

 

Veröffentlicht : 19/09/2023 1:59 pm
PGe-10
(@pge-10)
Active Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

I only have 2 Mini+ so I only dare to test it on one, after all it's only an Alpha version and I'm not brave enough to dare to run on both

Posted by: @cwbullet

I appreciate that.  I am not sure about what is causing it.  One printer worked.  One went into a perpetual boot loop when I tried to update to 4.4.1.  A third would not recognize the input shaper firmware.  I guess that means I will be trying a fourth tonight.  

Posted by: @pge

 

I'm very sorry, I meant no harm. On the contrary, I wanted to try to help

 

 

Veröffentlicht : 19/09/2023 2:06 pm
kevman
(@kevman)
Estimable Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

still having homing issues. I checked the belt tension with the tool, I tried some suggested commands from the bug page on github:

M914 X140

G28 X

That worked , but when I started the print it failed again with the homing error. 

Veröffentlicht : 19/09/2023 2:09 pm
Smiley85
(@smiley85)
Active Member
RE:
  • Ah my fails the y axis test. Reverted back to 4.4.1 and it's fine. Upgraded back to this alpha and it fails again. 
Diese r Beitrag wurde geändert Vor 1 year 2 mal von Smiley85
Veröffentlicht : 19/09/2023 2:18 pm
Neolker
(@neolker)
Mitglied
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

Belts must be tune pretty well for Input Shaper: https://belt.connect.prusa3d.com/

Veröffentlicht : 19/09/2023 2:40 pm
Smiley85
(@smiley85)
Active Member
RE: 5.1.0-alpha1 Firmware for Original Prusa MINI/MINI+ with Input Shaper and Prusa Connect!

 

Posted by: @neolker

Belts must be tune pretty well for Input Shaper: https://belt.connect.prusa3d.com/

That's a pretty cool feature. I just tried and both x and y were fine.

Veröffentlicht : 19/09/2023 3:22 pm
Andy Piper gefällt das
Seite 2 / 8
Teilen: