Benachrichtigungen
Alles löschen

Unofficial Prusa Mini Wait Thread  

Seite 34 / 241
  RSS
Crawlerin
(@crawlerin)
Prominent Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @bobstro
Notice it seems they're officially doing a 2-step filament warmup: 170C before mesh bed leveling, then up to full temp.

Yeah, that's rather neat. Other things I have noticed so far:

  • No power loss protection - but that was written in announcement blog post, it will come later with FW update
  • No XYZ calibration for frame skew - not sure if that's because it's not needed due to construction, or not implemented yet. Points for induction probe are on heatbed.
  • There is this initial confusion as to which button is highlighted on display - the white one or the blue one?
  • 9 gummy bears. Manual clearly documents and requires 10. Should we ask to ship one extra mini bear as part of warranty claim? 🤔
Veröffentlicht : 12/12/2019 11:53 pm
Olef
 Olef
(@olef)
Prominent Member
RE: Unofficial Prusa Mini Wait Thread

So, things noted so far as well as the two step filament heating - no xyz calibration, no crash detect, no power panic

Edit - crawlerin and I posted at the same time 🙂

Veröffentlicht : 13/12/2019 12:10 am
cwbullet
(@cwbullet)
Mitglied
Themenstarter answered:
RE: Unofficial Prusa Mini Wait Thread

Very interesting video.  Looking forward to owning one.

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 13/12/2019 12:17 am
cwbullet
(@cwbullet)
Mitglied
Themenstarter answered:
RE: Unofficial Prusa Mini Wait Thread

@crawlerin

I demand 10 gummy bears.

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 13/12/2019 12:19 am
Crawlerin
(@crawlerin)
Prominent Member
RE: Unofficial Prusa Mini Wait Thread

Oooh, network connectivity with webpage. Really barebones ATM, reads temperatures, almost everything is "Under contruction". There will be tab "Account" - will this link to Prusa account?

That reminds me, I will need to put it into IPv6-only VLAN to see what it does 🤣 

Diese r Beitrag wurde geändert Vor 5 years von Crawlerin
Veröffentlicht : 13/12/2019 12:27 am
pingu
(@pingu)
Estimable Member
RE: Unofficial Prusa Mini Wait Thread

woundering if the rods on the free hanging end are threaded and screwed to the pritned part. well, if thinking about it, thats the only posibility for its rigidty. 

 

@grey beard3d: thank you so much for this stream!

Veröffentlicht : 13/12/2019 12:38 am
Sink
 Sink
(@sink)
Estimable Member
RE: Unofficial Prusa Mini Wait Thread

Got my shipment notice yesterday .. unexpected Xmas gift next week ..

Veröffentlicht : 13/12/2019 4:29 am
Greybeard3D
(@greybeard3d)
Estimable Member
RE: Unofficial Prusa Mini Wait Thread

Congrats Gary. I assume it will arrive Monday. 

We should talk about some positives too. 

- mk3 bed plate ‘compatibility’. 
- Filament awareness

- handled ninjaflex very well. Honestly on par with my mk3 experience. 
- Very quiet. 
- beautiful screen. Yes, very first prompt was confusing to which is highlighted. 

And some things not mentioned

- filament loading first time was different. Needs more shove than mk3. 
- Ninjaflex didnt fully unload first time  

- unloading filament leaves the heater on. (Not in video)

- loading filament if it fails for first layer calibration on initial setup only gave one retry and no option for more (reset needed)

 

if anyone wants me to try anything else let me know. 

Veröffentlicht : 13/12/2019 7:27 am
Richard__H gefällt das
Clemens M.
(@clemens-m)
Noble Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @phr0ze

...

if anyone wants me to try anything else let me know. 

YES - here is my wish: Please send your printer to me - you can have mine - will come in January! 😉

Reading through the reviews, I hope they will put major efforts on bug fixing!

Best regards,
Clemens Mödlin

Mini, i3 MK2.5S, i3 MK4, CClone (Eigenbau)

Veröffentlicht : 13/12/2019 9:00 am
Crawlerin
(@crawlerin)
Prominent Member
RE: Unofficial Prusa Mini Wait Thread

There are reviews already posted?

Yes the firmware looks a bit undercooked, but in general, is it safe to say that printer does its job? Would complete newb buying this printer be able to set it up and get going?

BTW how was the Buddy print? IIRC speed was turned up to like 200% and it handled it well. I am glad to hear that it works with ninjaflex too. 

Veröffentlicht : 13/12/2019 9:46 am
Richard__H
(@richard__h)
Active Member
RE: Unofficial Prusa Mini Wait Thread

@phr0ze

Thankyou for the updates - really pleased to hear that flexibles are OK.

Did I see that some 240V and Filament Sensor builds are now being shipped ?

R

Veröffentlicht : 13/12/2019 10:23 am
cwbullet
(@cwbullet)
Mitglied
Themenstarter answered:
RE: Unofficial Prusa Mini Wait Thread

google mini tracker

I can't figure why some have shipped over others.  Looks like the sensors are shipping.  

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 13/12/2019 10:51 am
Richard__H gefällt das
Olef
 Olef
(@olef)
Prominent Member
RE: Unofficial Prusa Mini Wait Thread

@Charles-h13

Always happens with a major ship. They never follow the order number sequence, probably related to how ready each kit is to ship.

Veröffentlicht : 13/12/2019 11:17 am
cwbullet
(@cwbullet)
Mitglied
Themenstarter answered:
RE: Unofficial Prusa Mini Wait Thread

@olef

There must be a method to their madness.  

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 13/12/2019 11:20 am
Bodo
 Bodo
(@bodo)
Estimable Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @charles-h13

google mini tracker

I can't figure why some have shipped over others.  Looks like the sensors are shipping.  

Both outliers are orders from the 13th, both are black, both have no filament sensor.

Maybe a case of having no Filament-Sensors at hand, and only black printers, but the need to empty the packing table in order to continue with the next batch?

None of the orders in our wait list have this configuration after the last order shipped from the 12th.

Veröffentlicht : 13/12/2019 11:24 am
cwbullet
(@cwbullet)
Mitglied
Themenstarter answered:
RE: Unofficial Prusa Mini Wait Thread

Think we will see a lot of progress today.  I still wonder how many got shipping info but did nto post an update.  

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 13/12/2019 11:45 am
Richard__H gefällt das
Richard__H
(@richard__h)
Active Member
RE: Unofficial Prusa Mini Wait Thread

I'm shipped - 2 x Black Minis with Filament Sensors and both Sheets to the UK

Whoop !

Edit - spreadsheet updated

Diese r Beitrag wurde geändert Vor 5 years von Richard__H
Veröffentlicht : 13/12/2019 11:51 am
Texy
 Texy
(@texy)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @crawlerin
Posted by: @bobstro
Notice it seems they're officially doing a 2-step filament warmup: 170C before mesh bed leveling, then up to full temp.

Yeah, that's rather neat. Other things I have noticed so far:

  • No power loss protection - but that was written in announcement blog post, it will come later with FW update
  • No XYZ calibration for frame skew - not sure if that's because it's not needed due to construction, or not implemented yet. Points for induction probe are on heatbed.
  • There is this initial confusion as to which button is highlighted on display - the white one or the blue one?
  • 9 gummy bears. Manual clearly documents and requires 10. Should we ask to ship one extra mini bear as part of warranty claim? 🤔

..so is white or blue highlighted the right choice ?

Veröffentlicht : 13/12/2019 11:57 am
Richard__H gefällt das
Crawlerin
(@crawlerin)
Prominent Member
RE: Unofficial Prusa Mini Wait Thread

@texy

White. 

Veröffentlicht : 13/12/2019 12:37 pm
Richard__H gefällt das
cwbullet
(@cwbullet)
Mitglied
Themenstarter answered:
RE: Unofficial Prusa Mini Wait Thread

I prefer purple.  

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 13/12/2019 1:15 pm
Seite 34 / 241
Teilen: