Notifications
Clear all

Unofficial Prusa Mini Wait Thread  

Page 100 / 241
  RSS
MileHigh3Der
(@milehigh3der)
Honorable Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @charles-h13

Has anyone else had problems with poor extrusion?  I had to adjust mine.  

What did you have to adjust?

Posted : 11/02/2020 4:08 am
Oxygen
(@oxygen)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

@bobcousins congrats

@littleneutrino do you need our help?

Mini with FW:4.4.1 + SuperPINDA + Bondtech Heatbreak + PC4-M8 couplers + 1 piece boden

Posted : 11/02/2020 6:48 am
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

5 printers were reported as shipped yesterday.

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 11/02/2020 10:02 am
cwbullet
(@cwbullet)
Member
Topic starter answered:
RE: Unofficial Prusa Mini Wait Thread

@hawwwran

Important stipulation: "off the country list".  

--------------------
Chuck H
3D Printer Review Blog

Posted : 11/02/2020 10:08 am
cwbullet
(@cwbullet)
Member
Topic starter answered:
RE: Unofficial Prusa Mini Wait Thread

@nathanwms

The profiles seem to be adequate.  

--------------------
Chuck H
3D Printer Review Blog

Posted : 11/02/2020 10:10 am
cwbullet
(@cwbullet)
Member
Topic starter answered:
RE: Unofficial Prusa Mini Wait Thread
Posted by: @milehigh3der
Posted by: @charles-h13

Has anyone else had problems with poor extrusion?  I had to adjust mine.  

What did you have to adjust?

I had to increase the tension on the extruder.  

--------------------
Chuck H
3D Printer Review Blog

Posted : 11/02/2020 10:11 am
sjrocky
(@sjrocky)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread

Well,  now I'm getting nervous.  Mine hasn't shipped yet (14OCT order). I leave on vacation right after work today, and I'll be gone for a few weeks. I've told some one that it may come while I'm gone, and I'm hoping that they will be watching for it. 

Last 3 digits of my order # "666". 

 

This shouldn't be a cause for alarm, should it?

Posted : 11/02/2020 11:15 am
cwbullet
(@cwbullet)
Member
Topic starter answered:
RE: Unofficial Prusa Mini Wait Thread

@scott-r20

That is my exact story.  The threaded the needle and I got it before my vacation.  Hopefully, it till hold till you get back.  You could chat and see if they can hold it till you return.  

--------------------
Chuck H
3D Printer Review Blog

Posted : 11/02/2020 11:19 am
sjrocky liked
Derek
(@derek)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread

@charles-h13

Were you ever able to get it to print with the TXT plate?  I'm really struggling.  I'm surprised there's not a thread about this yet.

Posted : 11/02/2020 11:59 am
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @charles-h13

@hawwwran

Important stipulation: "off the country list".  

That was response to the question whether there was a single printer shipped yesterday according to the sheet. I just replied without quote, my fault.

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 11/02/2020 12:18 pm
Lichtjaeger
(@lichtjaeger)
Noble Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @derek

@charles-h13

Were you ever able to get it to print with the TXT plate?  I'm really struggling.  I'm surprised there's not a thread about this yet.

There are even heaps of posts complaining about problems with powder-coated sheets.

I can't confirm the problems, though. After receiving it I cleaned the plate according to the known procedure and since then everything is fine. Even with PLA.

But if I have a model that tends to warp I still prefer the smooth sheet for PLA just for the extra bit of adhesion.

Posted : 11/02/2020 12:19 pm
Derek
(@derek)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread

@lichtjaeger

What's the known procedure?

Posted : 11/02/2020 12:21 pm
Clemens M.
(@clemens-m)
Noble Member
RE: Unofficial Prusa Mini Wait Thread

@scott-r20

BEAST !!! 😉

Best regards and good luck, Clemens Mödlin

Mini, i3 MK2.5S, i3 MK4, CClone (Eigenbau)

Posted : 11/02/2020 12:36 pm
sjrocky liked
Lichtjaeger
(@lichtjaeger)
Noble Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @derek

@lichtjaeger

What's the known procedure?

Don't touch the sheet with bare hands.

  1. Whip both sites with soapy water and clean paper towels
  2. Rinse with clear warm water
  3. Do a dry wipe using clean paper towels
  4. Use the preheated bed (85°C) to dry it completely and to prevent rust
  5. Let it cool down
  6. Do a final wipe with IPA
  7. Don't touch it with bare hand ever again
Posted : 11/02/2020 12:36 pm
sjrocky
(@sjrocky)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @lichtjaeger
Posted by: @derek

@lichtjaeger

What's the known procedure?

Don't touch the sheet with bare hands.

  1. Whip both sites with soapy water and clean paper towels
  2. Rinse with clear warm water
  3. Do a dry wipe using clean paper towels
  4. Use the preheated bed (85°C) to dry it completely and to prevent rust
  5. Let it cool down
  6. Do a final wipe with IPA
  7. Don't touch it with bare hand ever again

For the IPA, do you prefer Foundrers All Day IPA, or something like Victory DirtWolf Double IPA?

Posted : 11/02/2020 1:12 pm
cwbullet
(@cwbullet)
Member
Topic starter answered:
RE: Unofficial Prusa Mini Wait Thread
Posted by: @scott-r20
Posted by: @lichtjaeger
Posted by: @derek

@lichtjaeger

What's the known procedure?

Don't touch the sheet with bare hands.

  1. Whip both sites with soapy water and clean paper towels
  2. Rinse with clear warm water
  3. Do a dry wipe using clean paper towels
  4. Use the preheated bed (85°C) to dry it completely and to prevent rust
  5. Let it cool down
  6. Do a final wipe with IPA
  7. Don't touch it with bare hand ever again

For the IPA, do you prefer Foundrers All Day IPA, or something like Victory DirtWolf Double IPA?

I am not so sure 7 is needed.  I touch the edges with my bare hands.  

--------------------
Chuck H
3D Printer Review Blog

Posted : 11/02/2020 1:13 pm
cwbullet
(@cwbullet)
Member
Topic starter answered:
RE: Unofficial Prusa Mini Wait Thread
Posted by: @lichtjaeger
Posted by: @derek

@lichtjaeger

What's the known procedure?

Don't touch the sheet with bare hands.

  1. Whip both sites with soapy water and clean paper towels
  2. Rinse with clear warm water
  3. Do a dry wipe using clean paper towels
  4. Use the preheated bed (85°C) to dry it completely and to prevent rust
  5. Let it cool down
  6. Do a final wipe with IPA
  7. Don't touch it with bare hand ever again

I responded to the wrong message.  I am not sure 7 is needed.  You can touch the edges.  

--------------------
Chuck H
3D Printer Review Blog

Posted : 11/02/2020 1:14 pm
MileHigh3Der
(@milehigh3der)
Honorable Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @scott-r20
Posted by: @lichtjaeger
Posted by: @derek

@lichtjaeger

What's the known procedure?

Don't touch the sheet with bare hands.

  1. Whip both sites with soapy water and clean paper towels
  2. Rinse with clear warm water
  3. Do a dry wipe using clean paper towels
  4. Use the preheated bed (85°C) to dry it completely and to prevent rust
  5. Let it cool down
  6. Do a final wipe with IPA
  7. Don't touch it with bare hand ever again

For the IPA, do you prefer Foundrers All Day IPA, or something like Victory DirtWolf Double IPA?

I see what you did there... Cheers!

Posted : 11/02/2020 1:42 pm
sjrocky liked
Lichtjaeger
(@lichtjaeger)
Noble Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @charles-h13
Posted by: @lichtjaeger

Don't touch the sheet with bare hands.

  1. Whip both sites with soapy water and clean paper towels
  2. Rinse with clear warm water
  3. Do a dry wipe using clean paper towels
  4. Use the preheated bed (85°C) to dry it completely and to prevent rust
  5. Let it cool down
  6. Do a final wipe with IPA
  7. Don't touch it with bare hand ever again

 I am not sure 7 is needed.  You can touch the edges.  

Ok, the edges and corners. But only the edges and corners.

Posted : 11/02/2020 1:53 pm
Seth
 Seth
(@seth-2)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread

@hawwwran

Mine was one of them, expected delivery by FEDEX tomorrow

Posted : 11/02/2020 2:04 pm
Page 100 / 241
Share: