English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum General discussion, announcements and releases Avisos Vaciar todo General discussion, announcements and releases | RSS Página 155 / 196 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Polyalchemy producing again? Por Jacob Kinchelo... on May 28, 20 2190 4 Jacob Kinchel... Prusament Quality Control Por Sam_PNW on May 27, 20 7199 22 debra.k Help: Suggested Test Prints Por cwbullet on May 27, 20 2224 6 cwbullet Make your 3D prints stronger with titanium rod... Por cwbullet on May 27, 20 2453 2 coolRR bed adhesion ? Por Neophyl on May 27, 20 1735 2 layden_blackw... Slicr3D Best Infill Por Grandpa Joe on May 26, 20 2292 1 Grandpa Joe 9 suggestions for Original Prusa i3 MK4 Por CovertPluto350... on May 26, 20 3009 3 CovertPluto35... Prusament PC Blend Por 3D Printing Sc... on May 26, 20 4444 6 nic Heat bed sensor problem Por keelanforrests on May 25, 20 2734 9 kevin.k33 First layer Por Frans Krau on May 23, 20 2445 2 kenatno10 older version of prusaslicer Por bobstro on May 22, 20 10194 10 tpsmidsltd Unlocked Firmware Por bobstro on May 22, 20 3577 4 jim Problems with first layer of supports Por bobstro on May 22, 20 2573 2 katharine.p2 Sudden X or Y shifts Por BobinAtlanta on May 21, 20 2365 3 BobinAtlanta Bellus3D Face Mask Fitter for COVID-19 Por ChristinaR on May 20, 20 3105 5 ChristinaR Review: PolyMaker PolyBox Por cwbullet on May 20, 20 6953 1 cwbullet Possible underextrusion Por Emily on May 19, 20 1820 3 Emily Mask out a section of printing DURING a print Por 3DALHEMIJA on May 18, 20 1847 2 Mat What's the problem with moisture? Por Paul on May 18, 20 5832 8 RedDawg self introduction Por jiangann34 on May 18, 20 1802 1 jiangann34 Página 155 / 196 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Siguiente Compartir: