English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Stránka 152 / 195 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author How can I get rid of these vertical lines? Od 3Dean Printing on Jun 18, 20 2319 3 AbsoluteMaker Overhang checking in PursaSlicer Od prusanewuser on Jun 17, 20 1576 1 prusanewuser Range of OK live Z values. Od Crawlerin on Jun 17, 20 2020 2 towlerg Unknown Printer Model Od Olef on Jun 16, 20 2196 2 Danyal Glue for printbed? Od Sasaki on Jun 15, 20 12659 17 BobinAtlanta My Mk2 bed is much cooler in the middle than t... Od RedDawg on Jun 15, 20 2270 4 shacharweis Can the time to finish printing be more accura... Od prusanewuser on Jun 15, 20 2049 1 prusanewuser What is the recommended values for top and bot... Od prusanewuser on Jun 15, 20 18605 7 prusanewuser Filament opacity for 3D printed cameras Od Sam_PNW on Jun 15, 20 3526 5 Sam_PNW Why circular holes are not circular? Which pla... Od prusanewuser on Jun 13, 20 8093 17 prusanewuser Consistent crashing since new firmware update Od DayOutBreeze on Jun 13, 20 2002 3 DayOutBreeze Prusa slicer on raspberry pi 4 (4GB) Od cliffmedina007 on Jun 12, 20 10952 8 peter.h16 Orientation upon importing to Prusa Slicer Od Neophyl on Jun 09, 20 3104 3 prusanewuser Shipping delay Od CCJack on Jun 09, 20 10942 24 Joeri What to do while I wait? Od Crawlerin on Jun 08, 20 3006 5 nodaysoff360 Is the Orange PLA different than Prusament Ora... Od Crawlerin on Jun 08, 20 3243 3 Matt Boyer Prusament Design Challenge Od Matt Boyer on Jun 08, 20 3077 13 Matt Boyer 9 suggestions for Original Prusa i3 MK4 ? Od CovertPluto350... on Jun 07, 20 3176 3 edgarismaelei... prints not sticking to bed Od lindley5 on Jun 07, 20 1845 4 lindley5 Post printing processing Od mark_glasson on Jun 07, 20 1620 2 towlerg Stránka 152 / 195 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 Další Share: