|
@crawlerin, you hit the nail on the head 🥀 . as the bed heat... Dans le forum Assembly and first prints troubleshooting |
il y a 4 years |
|
to jsou ale dva zakladni predpoklady uspesneho tisku - cista... Dans le forum Jak to vytisknu? (Pomoc s tiskem) |
il y a 4 years |
|
@divis-petr Pokud to mas v zaruce, posli to na reklamaci. Zk... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |
|
Zavisí hodně na materiálu. PETG nedrží moc na texturované po... Dans le forum Rady k tisku (Archiv) |
il y a 4 years |
|
@divis-petr tak to je malinko z ruky. Nezkoušel jsi se vráti... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |
|
ochranny kryt neni vselek, doporucuje se pouzivat zejmena pr... Dans le forum Original Prusa i3 MK3 & MK3S & MK3S+ |
il y a 4 years |
|
(@divis-petr) Jak to vypadá? Asi nemáš možnost zkusit jiný k... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |
|
Nemusí to být přímo slicerem, ale jak Baron podotkl, treba n... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |
|
Škoda ze nehledas, protože by ses třeba dočetl co znamená do... Dans le forum Rady k tisku (Archiv) |
il y a 4 years |
|
Špatně napnutí řemenu nebo nedotažená řemenice, tření ložis... Dans le forum Jak to vytisknu? (Pomoc s tiskem) |
il y a 4 years |
|
Zdravim, Nejsem si jist že 3d tisk je pro sériovou výrobu ne... Dans le forum Jak to vytisknu? (Pomoc s tiskem) |
il y a 4 years |
|
Stane se to, když filamentu něco brání v pohybu - zepredu má... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |
|
Nejdrive bych doporučil najít tady ne webu, jak pořádně očis... Dans le forum Original Prusa i3 MK3 & MK3S & MK3S+ |
il y a 4 years |
|
@michal-f5 bylo by super, dodat více informací, minimálně to... Dans le forum Složení tiskárny a řešení potíží s prvním tiskem |
il y a 4 years |
|
mam pocit,ze purge vytlacuje rychlosti 100% nezavisle na dru... Dans le forum Jak to vytisknu? (Pomoc s tiskem) |
il y a 4 years |
|
MINI má hodně daleko kolečka extruderu od trysky, co může mí... Dans le forum Jak to vytisknu? (Pomoc s tiskem) |
il y a 4 years |
|
@lemak13 gratuluji. @divis-petr nebude tvůj problém stejný? Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |
|
možná zcetny dotaz, mate oba originální Prusa tiskárnu, že? ... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |
|
jen tak mimochodem,odkud jste nahráli verzi 3.9.0 ? Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |
|
takze uz ani 3.8.1 ti nedovolilo cestinu? tak kontaktuj tech... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 4 years |