|
@tomas-2, jen kontolní dotaz - při unloadu filamentu má tisk... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 5 years |
|
Hi @brandon-c18, did you get resolved you issue? If so, I wo... Dans le forum General discussion, announcements and releases |
il y a 5 years |
|
Zkusme rozdělit problém na dvě základní části: - tryska se o... Dans le forum Obecná diskuze, oznámení a novinky |
il y a 5 years |
|
Ahoj, a co znamená "nedaří se"? pokud jsou ta kolečka moc m... Dans le forum Jak to vytisknu? (Pomoc s tiskem) |
il y a 5 years |
|
3d designer doda .stl soubor. Ten je zpracovan slicerem kter... Dans le forum Jak to vytisknu? (Pomoc s tiskem) |
il y a 5 years |
|
Co takhle zkusit malinko naolejovat tyče? Na nekolika vlakne... Dans le forum Rady k tisku (Archiv) |
il y a 5 years |
|
Jak to dopadlo? Vse v pohode? Dans le forum Rady k tisku (Archiv) |
il y a 5 years |
|
Super blahopreji. 😊 Dans le forum Hardware, firmware a software (Pomoc) |
il y a 5 years |
|
Btw netisknes nahodou v enclosure? Dans le forum Složení tiskárny a řešení potíží s prvním tiskem |
il y a 5 years |
|
Jak vypada to přeskakování? Je uzvejkany filament na miste o... Dans le forum Složení tiskárny a řešení potíží s prvním tiskem |
il y a 5 years |
|
Zkusil jsi vypnout nastaveni - Ventilator vzdy zapnuty? Toto... Dans le forum Obecná diskuze, oznámení a novinky |
il y a 5 years |
|
Moving your post to english forum, you could get more answer... Dans le forum How do I print this? (Printing help) |
il y a 5 years |
|
Btw. Do you have mk3 or mk3s? It is important as each of the... Dans le forum How do I print this? (Printing help) |
il y a 5 years |
|
Hi @luka-d6 Could be a coincidence. I would suspect the fila... Dans le forum How do I print this? (Printing help) |
il y a 5 years |
|
MINI bude take mit webove rozhrani, jen nevim presne co vsec... Dans le forum Složení tiskárny a řešení potíží s prvním tiskem |
il y a 5 years |
|
A co takhle pouzit bezdratovou flashku? Dans le forum Složení tiskárny a řešení potíží s prvním tiskem |
il y a 5 years |
|
Á ja zapomel bavime se o mini. A proc pripojeni pres USB? Dans le forum Složení tiskárny a řešení potíží s prvním tiskem |
il y a 5 years |
|
@pidra W7 by mělo být kompatibilní, nejde připojit pronterfa... Dans le forum Složení tiskárny a řešení potíží s prvním tiskem |
il y a 5 years |
|
@holecmirek Porad to jeste zlobi?pokud jo, zkusime spolu zji... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 5 years |
|
Zdravim, myslim ze pro limec to nejde nastavit je tu jen vol... Dans le forum Hardware, firmware a software (Pomoc) |
il y a 5 years |