Prusa3D Forum

Notifications

Clear all

Volker Jaenisch

Groupe: Enregistré

A(ont) rejoint: 2019/09/28

Trusted Member

	Have to put the file in the folder "filament"? Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jonathan-2 The link in my former post is broken. Points to ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@dsgn-dv I chose the 0.15 Quality AND the filaflex Profile. ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Dear @gerardo-w! The achievement that made my day was twofol... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@all good news! Today the new thermal paste arrived. I reass... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Dear @all! A merry christmas to you! May thanks for all the ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Dear @all! I changed the heatbreak to the original E3D one (... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Dear @all! Yesterday I printed some Test-Parts utilizing PLA... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Dear @antimix Where to buy such (2.3mm) tubes? Cheers, Volke... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Dear @antimix! Since this topic is started by myself I do no... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Testing for heat problems: Activated active cooling of the s... Dans le forum How do I print this? (Printing help)	il y a 5 years
	It is a time/temperature problem! Printing several wedges l... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@cevans9921 I am still not convinced that the problem is cau... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Dear @david-a66! the issue will be slight over/under extrusi... Dans le forum How do I print this? (Printing help)	il y a 5 years
	This works! Filamentum PLA Cristal ClearTemperature 230/60Ex... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Sorry have to correct myself. So I will try again with the e... Dans le forum How do I print this? (Printing help)	il y a 5 years
	First successfull print! Printed with no enclosement (23 Deg... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@all Thanks for your warm words. Today I replaced the side f... Dans le forum How do I print this? (Printing help)	il y a 5 years
	With the new extrusion stepper cooling, the outcome is excac... Dans le forum How do I print this? (Printing help)	il y a 5 years
	You are welcome! Wihout your (plural) generous help I would ... Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 1 / 4 Suivant

Statistiques du forum

565 Forums

63.6 K Sujets

446.3 K Messages

22 En-ligne

69 K Membres

Le dernier des messages: Original Beispiel/Test Drucke Notre nouveau membre: Kiley Murphy Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé