sylviatrilling – Activité

Notifications

Clear all

sylviatrilling

Groupe: Enregistré

A(ont) rejoint: 2021/07/03

Honorable Member

	The artifacts around the handle are seams. You can preview w... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	My understanding is that older attached files were simply de... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	Did you wash the plate with dishwashing detergent? IPA alone... Dans le forum How do I print this? (Printing help)	il y a 3 years
	I have noticed this too. If it gives me the option to print ... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	Another attempt at attaching a file: I simplified the model ... Dans le forum How do I print this? (Printing help)	il y a 3 years
	Are you using the latest version of PrusaSlicer? 2.4.0? Dans le forum How do I print this? (Printing help)	il y a 3 years
	For the line on your cup-holder, see/p> and also /p> and... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	This is the essential setting to get right and well worth th... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	If you make you z-offset lower in small increments, there is... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	It is puzzling, I did the same as you in Meshmixer, autorepa... Dans le forum How do I print this? (Printing help)	il y a 3 years
	From looking at the bottom of your benchy, I'd say your z-of... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	It suppose it won't attach because the file is too big. Me... Dans le forum How do I print this? (Printing help)	il y a 3 years
	D'oh! I zipped the repaired .stl but it won't attach. I'll t... Dans le forum How do I print this? (Printing help)	il y a 3 years
	The problem was with the model. I repaired it in Meshmixer a... Dans le forum How do I print this? (Printing help)	il y a 3 years
	You can use a modifier to apply 'ensure vertical wall thickn... Dans le forum How do I print this? (Printing help)	il y a 3 years
	You need to ZIP the .3mf file and then you will be able to a... Dans le forum How do I print this? (Printing help)	il y a 3 years
	Glad you at least got a print. I'm not getting any of those ... Dans le forum How do I print this? (Printing help)	il y a 3 years
	Please ZIP your .3mf file and attach to a post. (It must be ... Dans le forum PrusaSlicer	il y a 3 years
	Well, you're here on this forum, aren't you? It's a slippery... Dans le forum General discussion, announcements and releases	il y a 3 years
	I have been printing with Sandstone just fine on my SL1S. Be... Dans le forum How do I print this? (Printing help)	il y a 3 years

Page 11 / 30 Précédent Suivant

Statistiques du forum

565 Forums

63.6 K Sujets

446.2 K Messages

19 En-ligne

68.9 K Membres

Le dernier des messages: Repeated Probing on right side of bed Notre nouveau membre: Kiley Murphy Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé