ssill2 – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

ssill2

Gruppe: Registriert

Beigetreten: 2021/01/18

Noble Member

	@alexb this is so eerily reminiscent of the issue I saw with... Im Forum How do I print this? (Printing help)	Vor 5 years
	After getting the settings dialed in I had good success. I'... Im Forum How do I print this? (Printing help)	Vor 5 years
	I agree with dan about the zOffset. if this is off, you wo... Im Forum How do I print this? (Printing help)	Vor 5 years
	@swiss_cheese I agree! Your advice on this a few weeks ago ... Im Forum How do I print this? (Printing help)	Vor 5 years
	I will share my experience on the very same issue which I ha... Im Forum How do I print this? (Printing help)	Vor 5 years
	If you're already taking it in the shorts for that sub, yes ... Im Forum How do I print this? (Printing help)	Vor 5 years
	I will say that after printing TPU(Ninjaflex) again this mor... Im Forum How do I print this? (Printing help)	Vor 5 years
	@terry-8 I've only been printing a few months also and had t... Im Forum How do I print this? (Printing help)	Vor 5 years
	@xaimav yeah, dawn plantinum plus simple dish sponge scrubbe... Im Forum How do I print this? (Printing help)	Vor 5 years
	And of course hannibal mask with these settings fails... An... Im Forum How do I print this? (Printing help)	Vor 5 years
	Installed lol Im Forum How do I print this? (Printing help)	Vor 5 years
	@cwbullet yeah I will later today. unfortunately work is g... Im Forum How do I print this? (Printing help)	Vor 5 years
	@cwbullet Shelf for my wife's electric toothbrush, to get it... Im Forum How do I print this? (Printing help)	Vor 5 years
	Spoke too soon lol. I was sitting here and I noticed someth... Im Forum How do I print this? (Printing help)	Vor 5 years
	I used the following as a basic guide. Im Forum How do I print this? (Printing help)	Vor 5 years
	@neophyl It was several things. I've attached the zipped .3... Im Forum How do I print this? (Printing help)	Vor 5 years
	Did finally get this to print. I have a profile that works ... Im Forum How do I print this? (Printing help)	Vor 5 years
	@neophyl I do like their colors and I'm trying to standardiz... Im Forum How do I print this? (Printing help)	Vor 5 years
	@flashburn I've not tried to print at a .3mm layer height, s... Im Forum How do I print this? (Printing help)	Vor 5 years
	Just got another spool of the white Paramount3D PETG in. I... Im Forum How do I print this? (Printing help)	Vor 5 years

Seite 97 / 104 Vorherige Nächstes

Forums-Statistiken

598 Foren

71.8 K Themen

504.1 K Beiträge

12 Online

83.1 K Mitglieder

Letzter Beitrag: Mini LCD cable replacement Unser neuestes Mitglied: Print2Many Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen