ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	I looked at your .3mf. and since you've slowed down your r... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Not many things in 3d printing are as rewarding as finally g... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Yes, I had forgotten about that option, but I was going to m... Dans le forum How do I print this? (Printing help)	il y a 2 years
	for the sainsmart I do 3.5mvs, vs your 3.6. if you lower t... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I don't even use the spool inserts for the printdry. I just... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I don't feed the filament from the dry box. I just try the ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Are you getting filament wrapped around the extruder gear? ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Glad to help. In general stringing can be reduced by loweri... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I use the same tension for every material. You shouldn't ha... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Fair enough. you can get a lot of strength by paying with ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	you said your spool is marked as 220C as the top temp? If s... Dans le forum How do I print this? (Printing help)	il y a 2 years
	the 100% infill is really what is contributing to how long t... Dans le forum How do I print this? (Printing help)	il y a 2 years
	in my test prints, I'm using 1.5mm retraction length and 10 ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	you said it got further when you loosened idler right. can ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I'm not sure 40D is much different than 95A. Shore hardness... Dans le forum How do I print this? (Printing help)	il y a 2 years
	3.5 mvs is what I use. Use 10mm/s for retraction and detrac... Dans le forum How do I print this? (Printing help)	il y a 2 years
	just looked, I bought on jan 8, directly from them. Dans le forum How do I print this? (Printing help)	il y a 2 years
	I believe bought directly Dans le forum How do I print this? (Printing help)	il y a 2 years
	interesting, I bought my printdry pro 3 a few months ago and... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Well I look at my spools of sainsmart and the max temp on th... Dans le forum How do I print this? (Printing help)	il y a 2 years

Page 7 / 99 Précédent Suivant

Statistiques du forum

585 Forums

68.6 K Sujets

479.9 K Messages

11 En-ligne

76.9 K Membres

Le dernier des messages: Switch to Print Preview on machine Notre nouveau membre: Qohelath Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé