ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	@diem yeah I sort of convinced my wife it wasn't a good idea... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Ok, so petg is not really too bad to get printing. What most... Dans le forum Assembly and first prints troubleshooting	il y a 5 years
	This issue is quite similar to another user that's been post... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@dimensions-of-three supports material is by default printed... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I can deal with 5 interventions in 1510 filament changes. as... Dans le forum General discussion, announcements and releases	il y a 5 years
	And did I mention setting up steel sheet profiles? 🙂 Dans le forum How do I print this? (Printing help)	il y a 5 years
	@rob-12 Yes, I only started in November and as I said the fi... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@rob-12 Here's a .3mf for sainsmart tpu with the xzy cube in... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@gglockner yeah been there done that too. I have some filam... Dans le forum General discussion, announcements and releases	il y a 5 years
	I regularly use sainsmart pastel tpu, I could give you a pro... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I think you're going to have a difficult time printing that.... Dans le forum How do I print this? (Printing help)	il y a 5 years
	89%! just over 3 hours to go. A total of 5 minor interven... Dans le forum General discussion, announcements and releases	il y a 5 years
	and that's a nice looking part. Good job Dans le forum How do I print this? (Printing help)	il y a 5 years
	I find those go away. I've seen them before too, but they t... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Nice. I don't think you need the sandpaper, just a standard... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@swiss_cheese That would be fun with transparent fillament a... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@cwbullet So it appears that all this time my extruder idler... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@swiss_cheese status at 84% Dans le forum How do I print this? (Printing help)	il y a 5 years
	@swiss_cheese I have a set of assorted sandpapers coming tha... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@swiss_cheese Oh good! maybe I'm doing something right 🙂 Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 71 / 104 Précédent Suivant

Statistiques du forum

598 Forums

71.8 K Sujets

504 K Messages

18 En-ligne

83.1 K Membres

Le dernier des messages: Under-extrusion in certain layers, depending on the PETG prints Notre nouveau membre: Print2Many Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé