ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	@neophyl I have a whole spool to burn, I can give it a try :... Dans le forum How do I print this? (Printing help)	il y a 4 years
	well it started out good. the infill for the first several... Dans le forum How do I print this? (Printing help)	il y a 4 years
	the printer that can print tpu is tied up at the moment, but... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Did you ever find a solution to this? I was thinking about ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	So far so good! Layer 4 going down. This is promising. H... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese Yeah the aligned rectilinear seems to be doing... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@cwbullet yeah, about as good as I would expect I think othe... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese ok, before I started looking at these, here's ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@popepanator adhesion isn't really the problem lol if it cu... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@popepanator It’s the nature of the beast. Those long runs ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese Ah cool thank you sir! Will take a look at th... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese Yeah. I’ll mess with it more tomorrow. Been a... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I was only trying to recreate the settings as faithfully fro... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@steve-8 yep, usually that or the semiflex are good place to... Dans le forum How do I print this? (Printing help)	il y a 4 years
	usually you can start with one of the built in ones and then... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Go to configuration->Configuration Wizard-> filaments.... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Just for fun I'm going to try this model with S3D Dans le forum How do I print this? (Printing help)	il y a 4 years
	I tried to port the settings from S3D to prusa and had no su... Dans le forum How do I print this? (Printing help)	il y a 4 years
	A few questions, What brand and shore hardness. Prusa has s... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@fuchsr Even with the layerneer I've seen the corners of the... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 71 / 100 Précédent Suivant

Statistiques du forum

595 Forums

68.9 K Sujets

481.7 K Messages

13 En-ligne

77.5 K Membres

Le dernier des messages: Horizontal surface patterns / uneven layers Notre nouveau membre: HaydenWizard Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé