ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	I've been pretty busy with work so I've kind of slowed down ... Dans le forum How do I print this? (Printing help)	il y a 3 years
	I've not tried polysmooth myself, but I've liked the other p... Dans le forum How do I print this? (Printing help)	il y a 3 years
	As mentioned above, the printer firmware will allow you to c... Dans le forum How do I print this? (Printing help)	il y a 3 years
	I'm not sure. The scrubbing with hot water and dawn usually... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I would recommend posting some pictures and perhaps a zipped... Dans le forum How do I print this? (Printing help)	il y a 4 years
	you could try increasing heat a bit. Any backpressure at al... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Which sheet are you using? Smooth? You should use glue st... Dans le forum How do I print this? (Printing help)	il y a 4 years
	the idler bolt is super simple and I find I don't have to ch... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I find that with PETG I have a different zOffset, and a sepa... Dans le forum How do I print this? (Printing help)	il y a 4 years
	What nessuno and bob said. 100mm 1 layer(.2mm) square on a... Dans le forum How do I print this? (Printing help)	il y a 4 years
	You might also try lowering the temp just a little. It's a... Dans le forum How do I print this? (Printing help)	il y a 4 years
	So generally you'll want to: - Make sure your idler bolt is ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Not all TPU is the same. For instance, I have this coast... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Follow up from support this morning: " Hello,BVOH and PETG c... Dans le forum How do I print this? (Printing help)	il y a 4 years
	It HAS to be a better solution than trying to share one extr... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Ok, here was my rather unsatisfying, but kind of expected, r... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I use several manufacturers for filament, mostly what I can ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	pretty slick looking enclosure though. Dans le forum How do I print this? (Printing help)	il y a 4 years
	I ALWAYS use the advanced purge configuration to configure p... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Ok the drying of the petg didn't improve things. The one I ... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 41 / 100 Précédent Suivant

Statistiques du forum

585 Forums

68.7 K Sujets

480.6 K Messages

12 En-ligne

77.1 K Membres

Le dernier des messages: Failed to load image from file "E:\Program Files\Prusa3D\PrusaSlicer\resources\icons\splashscreen.jpg". Notre nouveau membre: mike Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé