ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	I agree with @fuchsr, tpu tends to stick nearly too well d... Dans le forum How do I print this? (Printing help)	il y a 11 months
	can you show us what the sliced model looks like? While I ... Dans le forum How do I print this? (Printing help)	il y a 11 months
	I don’t. I some esun dryers but I only use the print dry. ... Dans le forum How do I print this? (Printing help)	il y a 11 months
	Maybe do a good cleaning on the sheet? Is it satin sheet? Dans le forum How do I print this? (Printing help)	il y a 11 months
	Oh man. I use a print dry that will do up to 85C. Can show... Dans le forum How do I print this? (Printing help)	il y a 11 months
	it could be 216 works better for me because I print in an en... Dans le forum How do I print this? (Printing help)	il y a 11 months
	yeah I would agree with that. Both my MK4s were previously ... Dans le forum How do I print this? (Printing help)	il y a 11 months
	yeah something like 1mm. yes that span is quite large for t... Dans le forum How do I print this? (Printing help)	il y a 11 months
	your arachne seams look worse than mine for some reason Dans le forum How do I print this? (Printing help)	il y a 11 months
	definitely looks better than the arachne ones. I almost wo... Dans le forum How do I print this? (Printing help)	il y a 11 months
	so in the bottom picture on the left, what setting is that? Dans le forum How do I print this? (Printing help)	il y a 11 months
	No Joy Dans le forum How do I print this? (Printing help)	il y a 11 months
	You have to go to "Add Media" Now here's the rub. if you... Dans le forum How do I print this? (Printing help)	il y a 11 months
	others can chime in here, but I think the ugly seems could b... Dans le forum How do I print this? (Printing help)	il y a 11 months
	I think what's best is to pick a couple brands of tpu. My t... Dans le forum How do I print this? (Printing help)	il y a 11 months
	yeah I'll agree about the seams, but again, I'm not at all a... Dans le forum How do I print this? (Printing help)	il y a 11 months
	I'm not an expert by any means, but I've managed to make thi... Dans le forum How do I print this? (Printing help)	il y a 11 months
	on the XL I've printed as low as 215 when doing multi color ... Dans le forum How do I print this? (Printing help)	il y a 11 months
	Here was my first attempt. This was at 218C. not bad consid... Dans le forum How do I print this? (Printing help)	il y a 11 months
	I'm printing one of your test pieces at the moment. So far ... Dans le forum How do I print this? (Printing help)	il y a 11 months

Page 3 / 93 Précédent Suivant

Statistiques du forum

565 Forums

64.2 K Sujets

449.6 K Messages

20 En-ligne

70.4 K Membres

Le dernier des messages: ESP32 Cam Support Notre nouveau membre: shugobha Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé