PJR – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

PJR

Gruppe: Moderator

Beigetreten: 2015/06/01

Titel: Antient Member Moderator

	Hi Robert I can't quite see what's wrong from your photo; l... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Scott 2.2.0 and 2.2.1 both have the same Vref for the mo... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Roman Yes, on the initial (beta) 2.2.0 there were some p... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Latest Update... The print ran for about 20 hours and compl... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Juan Thanks for the update and suggestions. Josef is aw... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Lintuxie Please to be of assistance. Happy printing! P... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi guys Just finished a 14+ hour overnight print with firmw... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Robert The source files are here: I think all version... Im Forum Software (Archive)	Vor 10 years
	Hi Juan Looks like you have an issue similar to others on t... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Juan Great thanks for letting us know. Pleasure to assi... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	OK, try downloading the firmware again. You could also try ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Juan Can you please create a new folder on the root of y... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Josef Many thanks for the reply. I was relying on the a... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi there I have had this error a couple of times. All I do... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi guys I have been doing a bit of research into the steppe... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Yes, I knew I had read it somewhere: The original "quiet" ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Right, here is a view from the top. I was wrong earlier.... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	I have just had the printer on my desk to check it out. The... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Richard No I use OctoPrint. I am not wondering if I sho... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	OK, so it's not fixed. I sliced a part with Cura. Estimate... Im Forum Prusa i3 kit (Archive)	Vor 10 years

Seite 266 / 281 Vorherige Nächstes

Forums-Statistiken

598 Foren

71 K Themen

497.6 K Beiträge

14 Online

82.3 K Mitglieder

Letzter Beitrag: Failing prints when extruding small amounts - help needed Unser neuestes Mitglied: Teen Patti Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen