jurassic73 – Activité – Prusa3D Forum

Notifications

Clear all

jurassic73

Groupe: Enregistré

A(ont) rejoint: 2019/04/11

Estimable Member

	Exciting! Dans le forum How do I print this? (Printing help)	il y a 4 years
	I took the front end of the extruder apart and loosened the ... Dans le forum Hardware, firmware and software help	il y a 4 years
	Filament runs but stub is even with top of PTFE tube, nothin... Dans le forum Hardware, firmware and software help	il y a 4 years
	2 perimeters2 perimeters w/ 1mm fillet4 perimeters w/ 2mm fi... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Tried to design around this bulge... 7mm walls, 4mm base, 3m... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Can you please share the .stl for this? Trying a few things... Dans le forum How do I print this? (Printing help)	il y a 4 years
	If an object is made up of width and length dimensions that ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Question... does an internal fillet on the edge of the inter... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Great to hear! Dans le forum How do I print this? (Printing help)	il y a 4 years
	Thanks for the reply. Maybe next update... 🙂 Dans le forum How do I print this? (Printing help)	il y a 4 years
	Anyone know if the newly released slicer and firmware addres... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Warp after removal from plate - PETG - 215mm long print Dans le forum How do I print this? (Printing help)	il y a 4 years
	printing external perimeters first was part of the list of i... Dans le forum How do I print this? (Printing help)	il y a 4 years
	This has actually been in the back of my brain but something... Dans le forum How do I print this? (Printing help)	il y a 4 years
	What are the results of printing with two perimeters and the... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Crazy I can just go easily print this vase mode cube with gr... Dans le forum How do I print this? (Printing help)	il y a 4 years
	This is as far as I've gotten to improve my print as well wi... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I measured my 40x40x40 vase cube with micrometers in multipl... Dans le forum How do I print this? (Printing help)	il y a 4 years
	FWIW, I'm printing the right half of this with default PETG ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Hey Bobstro! Thanks for replying. I use your intro/purge li... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 4 / 8 Précédent Suivant

Statistiques du forum

559 Forums

62.8 K Sujets

442.5 K Messages

20 En-ligne

67.4 K Membres

Le dernier des messages: Printer parts from PETG in heated enclosure Notre nouveau membre: pinklemonade Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé