Josef Průša – Aktywność

Notifications

Clear all

Josef Průša

Grupa: Admin

Dołączył: 2015/04/26

Tytuł: Member Admin

	Super, budeme radit zakaznikum. In forum Nápady na zlepšení (Archiv)	10 years temu
	.hex je predkompilovany pro presne nasi konfiguraci. Zmeno v... In forum Software (Archiv)	10 years temu
	Je mozne ze jsem s updatovanym FW menul proud do motoru, s v... In forum Stavebnice Prusa i3 (Archiv)	10 years temu
	Hodne maly objekt. Klidne bych dal jeste vic kousku, taky mi... In forum Rady k tisku (Archiv)	10 years temu
	Pokud mate verzi tiskarny s LCD at uz 3mm (po updatu FW na p... In forum Rady k tisku (Archiv)	10 years temu
	😉 sweet prints In forum Awesome prints (Hall Of Fame)	10 years temu
	Can you check if the blower fan duct isnt damaged? If its br... In forum Print tips (Archive)	10 years temu
	Yep there is a slight difference in port mapping. RAMBo mini... In forum Prusa i3 kit (Archive)	10 years temu
	We have no problems with PLA sticking to ABS juice, But plai... In forum Prusa i3 kit (Archive)	10 years temu
	Poprosil bych o fotku problému, případně STL a váš g-code In forum Rady k tisku (Archiv)	10 years temu
	Rad se podivam na vase nastaveni Simplify3D, my jej pouzivam... In forum Nejlepší výtisky & tiskové tipy	10 years temu
	Dobry vecer, nastavil jsem vam tady na foru Pro hodnost 😉 ... In forum Nejlepší výtisky & tiskové tipy	10 years temu
	To bohuzel nebude tak snadné. Slic3r dává do prikazu G1 polo... In forum Rady k tisku (Archiv)	10 years temu
	You need to have the addons installed in your arduino In forum Prusa i3 kit (Archive)	10 years temu
	Can I ask for the cause of the problem? In case someone else... In forum Print tips (Archive)	10 years temu
	Roman is right, you need to include filament in the wire har... In forum Prusa i3 kit (Archive)	10 years temu
	It is possible if you have the heatbed cables near to the LC... In forum Prusa i3 kit (Archive)	10 years temu
	Máte filament od nás? Můžete prosím dát tisknout testovací p... In forum Rady k tisku (Archiv)	10 years temu
	We will replace it, no worries about that. We’ve been testin... In forum Prusa i3 kit (Archive)	10 years temu
	The fet will me fine 🙂 You can set it ant Configuration.h ... In forum Prusa i3 kit (Archive)	10 years temu

Strona 28 / 39 Wstecz Następny

Statystyki Forum

585 Fora

68.3 K Tematy

478.2 K Posty

10 Online

76.1 K Członkowie

Ostatni Post: The Cryogrip Pro Glacier plate is an excellent cheaper alternative to the Satin plate with one minor caveat on the Core One Najnowszy użytkownik:: ArtiVIVO Recent Posts Unread Posts Tags

Forum Icons: Forum contains no unread posts Forum contains unread posts

Ikony tematu: Not Replied Odwpowiedzi Aktywny Gorący Przyklejony Unapproved Rozwiązany Private Zamknięte