gnat – Activité – Prusa3D Forum

Notifications

Clear all

gnat

Groupe: Enregistré

A(ont) rejoint: 2018/12/03

Noble Member

	@ryan-c29 That's a bummer, but not unexpected about the resi... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	Last check before bed was at the 26 hour mark and the rubber... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@ryan-c29 Awesome. Hopefully they contain the water equally ... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	Those times should cover their "empty it between every print... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@ryan-c29 Good luck. How long do you plan to let it sit for? Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	So I sent a "hello?" email this morning and finally got a re... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	I put a rubber band on #2 last night. It hasn't quite been 1... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@piranhamousemods Nice simple fix. I'll see if I have a work... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	Soaking the bottom of the tank in 99% IPA did not dissolve o... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@bayes7m On a $200 printer I would expect to have to do such... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	The resin will leak more slowly due to the viscosity differe... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	Yeah I mentioned that (though I used tightening a drum head ... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@ryan-c29 Nah I don't trust it and trusting the tank is the ... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	I'd like to ask you to guess which is tank #1 after 72 hours... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	And down goes tank #3 after about 3 hours (next to my finger... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	Both my original failures were Prusa installed FEPs too. The... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	Well... That didn't take long. The tank I have given the ele... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@ryan-c29 Ouch... Regarding the o-ring and getting the tank ... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@ryan-c29 What screws did you go with? Hopefully not the $80... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@ryan-c29 That would be so much less messy than the silicone... Dans le forum Assembly and first prints troubleshooting	il y a 4 years

Page 12 / 60 Précédent Suivant

Statistiques du forum

559 Forums

62.7 K Sujets

441.8 K Messages

16 En-ligne

67.1 K Membres

Le dernier des messages: Discussion: Is the Prusa XL prone to generating perfectly spaced VFAs or are they isolated cases? Notre nouveau membre: pinklemonade Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé