gnat – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

gnat

Gruppe: Registriert

Beigetreten: 2018/12/03

Noble Member

	@ryan-c29 That's a bummer, but not unexpected about the resi... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	Last check before bed was at the 26 hour mark and the rubber... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@ryan-c29 Awesome. Hopefully they contain the water equally ... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	Those times should cover their "empty it between every print... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@ryan-c29 Good luck. How long do you plan to let it sit for? Im Forum Assembly and first prints troubleshooting	Vor 4 years
	So I sent a "hello?" email this morning and finally got a re... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	I put a rubber band on #2 last night. It hasn't quite been 1... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@piranhamousemods Nice simple fix. I'll see if I have a work... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	Soaking the bottom of the tank in 99% IPA did not dissolve o... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@bayes7m On a $200 printer I would expect to have to do such... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	The resin will leak more slowly due to the viscosity differe... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	Yeah I mentioned that (though I used tightening a drum head ... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@ryan-c29 Nah I don't trust it and trusting the tank is the ... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	I'd like to ask you to guess which is tank #1 after 72 hours... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	And down goes tank #3 after about 3 hours (next to my finger... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	Both my original failures were Prusa installed FEPs too. The... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	Well... That didn't take long. The tank I have given the ele... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@ryan-c29 Ouch... Regarding the o-ring and getting the tank ... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@ryan-c29 What screws did you go with? Hopefully not the $80... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@ryan-c29 That would be so much less messy than the silicone... Im Forum Assembly and first prints troubleshooting	Vor 4 years

Seite 12 / 60 Vorherige Nächstes

Forums-Statistiken

559 Foren

62.7 K Themen

441.8 K Beiträge

18 Online

67.1 K Mitglieder

Letzter Beitrag: Error: PRUSATOOLCHANGER Unser neuestes Mitglied: pinklemonade Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen