|
Somewhat off-topic, but remember that you already have a pre... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Note that the PWM control of the fan switches GND, not +5V. ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Wenn ich das Teil drucken müßte, würde ich es wahrscheinlich... Dans le forum Hilfe zur Hardware, Firmware und Software |
il y a 6 years |
|
Ah., sorry. Sehe gerade, daß du vermutlich das andere Teil m... Dans le forum Hilfe zur Hardware, Firmware und Software |
il y a 6 years |
|
Drucken? Modelle bei Thingiverse, "E3D Bowden Clip". Dans le forum Hilfe zur Hardware, Firmware und Software |
il y a 6 years |
|
Now including a tower done with constant extruder linearity ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
There is no contest at all. The Moons 0.9 on the extruder bl... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Still running the Moons MS17HA2P4100 0.9º OK on extruder....... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
I found reading around that the Rambo is limited to about 10... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Is this no name motor built like cr*p or usable?
Will it pro... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
As far as the overheating problem is concerned, I am afraid ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
MS17HA2P4100 is an even better match by spec. A pair of them... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Probably should boost the x axis homing a little. X-axis doe... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
That is a lot less hysteresis than the stock motors. Because... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
What we're trying to correct are position errors, not torque... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Very puzzling - but at the end of the section, it has a note... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
After some digging, I believe that for a 2 phase stepper the... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
I have been trying to get a modified sin^power working in a ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
If the EINSY is indeed unable to keep up in standard mode wi... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
I get 16 VFA's/ cm in the prints.
Stepper is
200 cycles / r... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
