|
Posted by: @ingybing ...Any help or pointer on what to se... Dans le forum Hardware, firmware and software help |
il y a 1 year |
|
If you prefer a rear-facing AC/Mains receptacle, I made this... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |
|
Overall the printer has been pretty consistent. Print qualit... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |
|
Oh yeah I saw that and figured it out.
The short answe... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Extruder motor Moons 0.9° - no firmware change needed? Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Kinda hard to tell, but it looks like the heat block is upsi... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
BTW you should print the Mk3s+ versions. They have a better ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
I just tried the firmware update from a desktop PC that has ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Hey I just built a Fysetc this week too. I already have 4 ge... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Is it plausible to add a menu item or g-code config option t... Dans le forum General discussion, announcements and releases |
il y a 3 years |
|
So I never bothered modifying the Mk2.x MiniRambo 1.3a board... Dans le forum Hardware, firmware and software help |
il y a 3 years |
|
I've using these 12"x 12"x 0.25" cork boards for 2+ years on... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
RE: drill holes to accept end-stop switch - print with incre... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Maybe the hole at the bottom left will work to add a block t... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Great question. M109 would work too, but keep in mind this g... Dans le forum PrusaSlicer |
il y a 3 years |
|
@poblupuablo, @clemens-m I love the concept. Simple and eleg... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 4 years |
|
Well the Mk2.5S+ has been running flawlessly for 1 month and... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 4 years |
|
@clarmrrsn @evs If the silicone sheet is in direct contact w... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 4 years |
|
@milos-v You could augment the Mk3S+ x-carriage to provide t... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 4 years |
|
Upgrade your Mk2.5/Mk2.5S to use the new Mk3S+ extruder Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 4 years |
