|
Thank you ! I will eventually have a unified connector or co... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Attached is a picture of my wire loom/connectors for the 60w... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Specs vs real world always gets me buddy 🙂 I always look at... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
One of the guys on the thread even added one to the heatbed.... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Correct. Like I mentioned, there was a very detailed thread ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
The purple wired pictured goes back to the thermistor input ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
It's the same header the mmu2 and filament sensor (bottom ro... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
I used pins 2 and 5 on the top row (one of them is the same ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
The E3D V6 hotend used in the Mk 3 is rated to operate in am... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
On the X axis... again... you ... are... awesome..
I swapped... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Your "bad" LDO was wired correctly right? The LDO's 0.9's wi... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
You might also try swapping your Moon's 0.9 that is on Y to ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
[quote=guy.k2 post_id=135878 time=1553981674 user_id=95162]
... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Oh my!!!...I want to give a huge thank you to guy.k2 and spa... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
I did this the first thing after the Mk3 came out except wit... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Here is what I did so far
Complete hotend change - E3D gold... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
X axis parts - I opted for igus linear bearings for the carr... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
I actually built a printer specifically around this mentalit... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
PU Belts are known to break for sure with 16t idlers and pul... Dans le forum Hardware, firmware and software help |
il y a 6 years |
|
I'm thinking of replacing them with a polyurethane equivale... Dans le forum Hardware, firmware and software help |
il y a 6 years |
