Prusa3D Forum

Notifications

Clear all

Chris P

Groupe: Enregistré

A(ont) rejoint: 2020/05/12

Eminent Member

	@pcweber Thanks Phil! Dans le forum User mods - OctoPrint, enclosures, nozzles, ...	il y a 4 years
	Just changed nozzle and noticed this.... Dans le forum User mods - OctoPrint, enclosures, nozzles, ...	il y a 4 years
	@neophyl Thank you so much for explaining this to me. I was ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@neophyl Unless I'm doing it wrong, this particular fan duct... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Thank you all for the responses!! Dans le forum How do I print this? (Printing help)	il y a 4 years
	Another question, I'm assuming that to replace the fan duct ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Thank you both for your responses. I have the Prusa orange P... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Also, why ABS and not ASA? I thought ASA was better and less... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Material choice for updated fan duct on MK3S Dans le forum How do I print this? (Printing help)	il y a 4 years
	@mark1 Thanks for clarifying. I'm going to try it. Dans le forum How do I print this? (Printing help)	il y a 4 years
	@mark1 Thanks. Is one better than the other? Dans le forum How do I print this? (Printing help)	il y a 4 years
	@pcweber Thanks for all the great info. When I get home I'm ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@nikolai-r I am not printing in an enclosure but I think the... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@pcweber That looks really good. I will check my nozzle agai... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@pcweber I did check the nozzle and it appears to be fine. I... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Thanks for the replies and help. I will adjust those setting... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Well I printed another model with the new settings and it di... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I'm printing it now with 3 perimeters and 10% infill. I'll l... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@neophyl Thanks for the reply. I found the perimeter value s... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Just printed at 205 ֯C and still has hull issue circumferent... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 1 / 2 Suivant

Statistiques du forum

559 Forums

63.1 K Sujets

443.7 K Messages

23 En-ligne

68 K Membres

Le dernier des messages: Prusa to Printed Solid ........... Thought it would be good Notre nouveau membre: etiennep Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé