|
Thank you again for sharing. After the Bunny carriage is ins... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
No worries, I'm already printing the X-carriage =) But stil... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Thank you. I'll try that too. I just lubricated all my bear... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
I gave it a try and it shifted again after about 10h. This t... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Worth a try. I'll report back. After 2-3 successful (bigger)... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
It is enabled but the print didn't stop and asked for "remov... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Looks like I don't get the 0.9 motors reliable to work 🙁 Pr... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
For me it never was the firmware directly but the way my pri... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
I found the culprit for the layer shift. I made a mistake wh... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
I mentioned before, homing issues solved itself after 2 refl... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
I read somewhere that the Slice thermistor isn't very accura... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
This is so weird. From the beginning. Cables are fine and I ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Restoring the default limits in Slic3r for stealth and there... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Marlin_main.cpp line 3177: lcd_setstatuspgm(_T(MSG_LOADING_... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
This is the whole section. Note that I added my "Anti blob" ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
There are but I think those values are not used at all. The ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
I recently regreased all my bearings whilst installing the n... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Are there limitations (Speed, Acceleration etc.) for using S... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
#Update 3 Found the culprit: Grub screw thread was busted. T... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Update on my bigger test print with stealth mode. I got som... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
