|
There is obviously some kind of bug in my code. I haven't ha... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |
|
The Mini does not actually probe the exact center. Given tha... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Looks pretty good to me @3Ddesign-bySimon! If you get it dow... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Check for any debris between the heated bed and steel sheet. Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Mine was going on 2 years without adjustment untill i had to... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
There might be two issues here. 1. You over squished your mo... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 4 years |
|
Please don't stress your bed like that! Loosen that side unt... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 4 years |
|
Replace the "intro line" section with the original Gcode. If... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 4 years |
|
That's a clear sign of the PTFE not sitting flush with the e... Dans le forum Hardware, firmware and software help |
il y a 4 years |
|
@vizon This mod is not intended to fix X-Z skew. In fact, th... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@kevman Probably not. Afair that cutting jig is for a knife,... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@bapski Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@landvogt1893 Please follow directions! See attached screens... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@landvogt1893 The only thing that might have caused this is ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@robee-shepherd Can you give me an example of unstripped out... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@landvogt1893 No, 3.5mm is too high. It must be at most 3mm.... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
Please read the up-to-date guide here:br />and use the PMSBL... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@hannes-b3A Absolutely works. You need to use the micro USB ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@straylit It's literally the first step of the directions on... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
|
@d0ugNote that the plot is exaggerated. You have an amazing... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 5 years |
