# generated by PrusaSlicer 2.4.0+win64 on 2022-05-04 at 14:12:44 UTC

[print:0.20mm NORMAL @CHIRON]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0
bridge_acceleration = 250
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 25
brim_separation = 0
brim_type = outer_only
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.1
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 25
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 34
extruder_clearance_radius = 47
extrusion_width = 0.45
fill_angle = 45
fill_density = 15%
fill_pattern = grid
first_layer_acceleration = 0
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 20
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 0
gcode_resolution = 0.0125
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 50
inherits = 0.20mm NORMAL @CREALITY
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 100
max_volumetric_speed = 0
min_skirt_length = 4
mmu_segmented_region_max_width = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{print_time}_{digits(layer_height,1,2)}mm_{temperature[0]}C_{filament_type[0]}_{printer_model}.gcode
overhangs = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 40
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
seam_position = nearest
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 1
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.38
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 40
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thick_bridges = 1
thin_walls = 0
threads = 16
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 30
top_solid_layers = 5
top_solid_min_thickness = 0
travel_speed = 150
travel_speed_z = 0
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 170
wipe_tower_y = 140
xy_size_compensation = 0

[printer:Anycubic Chiron]
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,400x0,400x400,0x400
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0\n;{layer_z}\n\n
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA @CREALITY"
default_print_profile = 0.16mm OPTIMAL @CREALITY
deretract_speed = 40
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
extra_loading_move = -2
extruder_colour = #FCE94F
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = Creality CR-10
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
machine_limits_usage = emit_to_gcode
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 500
machine_max_acceleration_retracting = 1000
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 500
machine_max_acceleration_y = 500
machine_max_acceleration_z = 100
machine_max_feedrate_e = 60
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.28
max_print_height = 450
min_layer_height = 0.08
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = 
print_host = 
printer_model = CR10
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_CR10\nPRINTER_HAS_BOWDEN
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 1
retract_length = 6
retract_length_toolchange = 1
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM140 S{first_layer_bed_temperature[0]} ; set final bed temp\nM104 S150 ; set temporary nozzle temp to prevent oozing during homing\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\nG1 Z50 F240\nG1 X2 Y10 F3000\nM104 S{first_layer_temperature[0]} ; set final nozzle temp\nM190 S{first_layer_bed_temperature[0]} ; wait for bed temp to stabilize\nM109 S{first_layer_temperature[0]} ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:Anycubic Kobra Max]
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,400x0,400x400,0x400
before_layer_gcode = ; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Anycubic PLA @MEGA0"
default_print_profile = 0.20mm NORMAL @MEGA0
deretract_speed = 30
end_gcode = M117 Cooling down...\nM104 S0 ; turn off extruder\nM107 ; Fan off\nM84 ; disable motors\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 ;X-20 Y-20 F240 ;move Z up a bit and retract filament even more\nG28 X0 ;move X to min endstops, so the head is out of the way\nG90 ;Absolute positionning\nG1 Y200 F3000 ;Present print\nM84 ;steppers off\nM300 P300 S4000\nM117 Finished.\n
extra_loading_move = -2
extruder_colour = #FFFF00
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = Anycubic Mega Zero
layer_gcode = ; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm
machine_limits_usage = emit_to_gcode
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 500
machine_max_acceleration_retracting = 500
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 500
machine_max_acceleration_y = 500
machine_max_acceleration_z = 100
machine_max_feedrate_e = 25
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 5
machine_max_jerk_e = 5
machine_max_jerk_x = 10
machine_max_jerk_y = 10
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.3
max_print_height = 450
min_layer_height = 0.1
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host = 
printer_model = MEGA0
printer_notes = Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_MEGA0
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 0
retract_length = 7
retract_length_toolchange = 1
retract_lift = 0.2
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nM117 Homing X/Y ...\nG28 X0 Y0 ;move X/Y to min endstops\nM117 Homing Z ...\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F240 ;move the platform down 15mm\nM117 Heating ...\nM104 S[first_layer_temperature]\n ; set extruder temp\nM109 S[first_layer_temperature]\n ; wait for extruder temp\nM117 Start cleaning ...\nG92 E0 ;zero the extruded length\nG1 F200 E10 ;extrude 10mm of feed stock\nG92 E0 ;zero the extruded length again\nM117 Intro line ...\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z[first_layer_height] F5000.0 ; Move to start position\nG1 X0.1 Y200.0 Z[first_layer_height] F1500.0 E15 ; Draw the first line\nG1 X0.4 Y200.0 Z[first_layer_height] F5000.0 ; Move to side a little\nG1 X0.4 Y20 Z0.3[first_layer_height] F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 E-1 F500 ; Retract filiment by 1 mm\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.3 F240 ; Move over to prevent blob squish\nG92 E0 ; Reset Extruder\nM117 Printing...\n
template_custom_gcode = 
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[presets]
print = 0.20mm NORMAL @MEGA0
sla_print = 0.05 Normal @SL1S
sla_material = Prusa Orange Tough @0.05 SL1S
printer = Anycubic Kobra Max
filament = Generic PLA @MEGA0
physical_printer =