Recent Posts

Forums | Topics

Page 2 / 31 Prev Next

	Topic Title	Forum
	Loud fan noise when starting up and printing! By Fakejordan 1 day ago \| Last Post: 16 hours ago	Hardware, firmware and software help
	Thank you. I will try that. 16 hours ago By Fakej... Fan speed is to the max on printer start or (usual... 18 hours ago By _Kasz... RE: Loud fan noise when starting up and printing! 1 day ago By Fakej...
	Diamondback nozzle clogged By DarthMuffin 3 days ago \| Last Post: 17 hours ago	Hardware, firmware and software help
	Thanks for the tip. I ordered a 1/16" 6" drill bit... 17 hours ago By Darth... So I've been reading this thread with the smug ass... 22 hours ago By hyige... Hi, sorry for my english. I had exactly the same p... 1 day ago By PaKo view all posts
	Prusa Slicer starts with a fixed object By WalterKonrad 21 hours ago \| Last Post: 18 hours ago	General discussion, announcements and releases
	I had it start appearing after I downloaded a proj... 18 hours ago By srmal... Thanks. Found and changed. Don't know why I added ... 21 hours ago By Walte... That's an MMU Purge pile place holder, If you don'... 21 hours ago By JoanT...
	Which light-weigth GCODE-Viewer? By h1ghK0 2 weeks ago \| Last Post: 18 hours ago	General software discussion
	NC Viewer is online, and it doesn't appear to supp... 18 hours ago By Mike ... Thank you! 1 day ago By h1ghK... I prefer NC Viewer for quick checks. It’s lightwei... 6 days ago By Sara ...
	Can't participate in the Printed Fabric” contest, By Propsmaker 19 hours ago \| Last Post: 19 hours ago	General discussion, announcements and releases
	Hi, I’d like to participate in the “Printed Fabric... 19 hours ago By Props...
	Weird pattern on surface - extrusion issues? By mbezzo 22 hours ago \| Last Post: 19 hours ago	Assembly and first prints troubleshooting
	Yes, it's the surface pattern - apologies on not b... 19 hours ago By mbezz... If it's the surface moire pattern, I had something... 20 hours ago By hyige... (I'm "extrapolating" as I haven't seen this patter... 21 hours ago By mnent...
	Initialisation impossible By ipm vos idées 19 hours ago \| Last Post: 19 hours ago	Assembly and first prints troubleshooting
	Hello, I’ve replaced the idler, but I don’t unders... 19 hours ago By ipm v...
	Printed Solid as a vendor By Tim 3 months ago \| Last Post: 20 hours ago	General discussion, announcements and releases
	Doesn't Prusa own some (or all) of PrintedSolid? I... 20 hours ago By hyige... With the new tariff/shipping update from Prusa, it... 1 day ago By viasa... Indeed, that doesn't seem too bad considering ther... 2 weeks ago By David... view all posts
	Tisk košíčku - po jedné straně se v určité vrstvě tisk nezdařil By Skritek198 2 days ago \| Last Post: 21 hours ago	Jak to vytisknu? (Pomoc s tiskem)
	Nedalo mi to a ještě jsem hledal. Chyba je už v mo... 21 hours ago By Skrit... Ahoj. Zkoušel jsem vytisknou košíček na fixky. Tis... 2 days ago By Skrit...
	Update firmware MK3s+ By David Cantrill 21 hours ago \| Last Post: 21 hours ago	Hardware, firmware and software help
	When I try to update firmware I get the following ... 21 hours ago By David...
	Using PTU By BrianPGB 2 days ago \| Last Post: 22 hours ago	General discussion, announcements and releases
	It will stick to the build sheet OK, in fact you a... 22 hours ago By Diem Ah! Sorry for the mix up of letters, but thank you... 1 day ago By Brian... I wasn't sure about your 'title' - but realize it ... 1 day ago By Cyclo...
	Add warning for "One layer of non-solid infill between bottom and top solid infill" By Randall Wald 23 hours ago \| Last Post: 22 hours ago	PrusaSlicer
	Maybe only pop the warning if there's a minimum su... 22 hours ago By Randa... Such a warning would be triggered in almost all pr... 22 hours ago By Diem The default 0.2mm layer height settings have four ... 23 hours ago By Randa...
	Thermal Grease Shipping Cost By KennyB 4 days ago \| Last Post: 22 hours ago	General discussion, announcements and releases
	Partsbuilt 3D carry many Prusa parts and they ship... 22 hours ago By ssmit... Is there any way to get Heatbreak Thermal Grease w... 4 days ago By Kenny...
	blobs on purge Tower By Jack Renders 1 month ago \| Last Post: 22 hours ago	General discussion, announcements and releases
	I went with 265C, and I am sorry for the mistake. 22 hours ago By Henk ... You're right. Stupid mistake. 22 hours ago By Henk ... Surely you mean 265C, not 165C. 1 day ago By LarGr... view all posts
	Failed to load image from file "E:\Program Files\Prusa3D\PrusaSlicer\resources\icons\splashscreen.jpg". By brianjordan 1 day ago \| Last Post: 23 hours ago	PrusaSlicer
	It is on Windows 11 where I keep the majority of ... 23 hours ago By brian... I assume a Windows OS. ?? Why is Prusa loaded on E... 1 day ago By ruggb... I have recently upgraded the slicer to 2.9.3 and a... 1 day ago By brian...
	0.25 nozzle PLA, extruder skips By boB 1 week ago \| Last Post: 24 hours ago	How do I print this? (Printing help)
	Update: I have printed many parts with Jessie beig... 24 hours ago By boB The reason I ended up getting a SLA (resin) printe... 1 week ago By hyige... One more photo to show what occurred. It all prin... 1 week ago By boB view all posts
	loctite... By evilphoton 1 day ago \| Last Post: 1 day ago	Assembly and first prints troubleshooting
	previously with my mk4s, when i would periodically... 1 day ago By evilp...
	Wobbly connectors on the cheese board By DXR_13KE 1 day ago \| Last Post: 1 day ago	Hardware, firmware and software help
	Is it normal for these parts on the cheese board t... 1 day ago By DXR_1...
	Any alternative for rivets? By Erwan 5 months ago \| Last Post: 1 day ago	User mods
	i wondered about the rivets too. but with the weig... 1 day ago By evilp... I learned to like these rivets. Aesthetic, easy to... 3 months ago By zapta RE: Any alternative for rivets? 3 months ago By k1mu view all posts