Recent Posts

Forums | Topics

Page 23 / 37 Prev Next

	Topic Title	Forum
	How did that happen? By Bryan_K 3 weeks ago \| Last Post: 3 weeks ago	How do I print this? (Printing help)
	So it happened again, this time during a short pri... 3 weeks ago By Bryan... I'm thinking its in the Z axis, but really hard to... 3 weeks ago By Tim I think there were only a few lines of infill on t... 3 weeks ago By Bryan... view all posts
	End g-code don't end at requested position By JanP 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I have also tried to use that standard End g-code ... 3 weeks ago By JanP I use the following End g-code in Pruse Slicer 2.9... 3 weeks ago By JanP
	Prusa Slicer isn't working on my MacBook Pro M1 By Richard3D 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	Problem solved, threw away the config and then it ... 3 weeks ago By Richa... Prusa Slicer crashes immediately when I start it. ... 3 weeks ago By Richa...
	Filamentende erkennen By Bienemaya 4 weeks ago \| Last Post: 3 weeks ago	Hilfe zur Hardware, Firmware und Software
	Danke. Das Filament ist gebrochen und er hat nicht... 3 weeks ago By Biene... Also, als erstes mal: Ne neue Düse brauchst da nic... 3 weeks ago By Digib... Hi zusammen, Ich habe jetzt Trouble gehabt, ... 4 weeks ago By Biene...
	Download print files from PrusaConnect By mrsam993 1 year ago \| Last Post: 3 weeks ago	Prusa Connect & PrusaLink
	I believe the USB drive is the file storage for th... 3 weeks ago By Green... Same here. I thought files stayed in Connect for a... 11 months ago By Razor Recently the USB for my Prusa Mk4 got corrupted an... 1 year ago By mrsam...
	setting up a BondTech extruder on the mini+ By Dan Borugã 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	RE: setting up a BondTech extruder on the mini+ 3 weeks ago By _Kasz... I would like to install the Bondtech extruder on m... 3 weeks ago By Dan B...
	G-Code Fehlerhaft auf USB Stick By Janus Kottisch 4 weeks ago \| Last Post: 3 weeks ago	Hilfe zur Hardware, Firmware und Software
	Da muss ich mal nachschauen was eingestellt ist. D... 3 weeks ago By Janus... Hast Du die Funktion "Power-loss recovery" (oder s... 3 weeks ago By Walte... Danke für deine ausführliche Antwort. Formatiert ... 3 weeks ago By Janus... view all posts
	Wifi no network interface after updating firmware to 6.2.4 By Larak 1 month ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	For anyone having the same problem: I got wifi con... 3 weeks ago By croml... I have the same problem after I updated my Mk4 fro... 3 weeks ago By croml... Hello, A few days ago I updated my prusa mk4 from ... 1 month ago By Larak
	Uninstalling Firmware Update on MK4 By eager 4 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Walter... Worked great. Thank you. 3 weeks ago By eager You must do this (pressing the knob 2 x) immediate... 4 weeks ago By Walte... I Googled this and it said to use a FAT32 flash dr... 4 weeks ago By eager view all posts
	"G-code sliced for a different printer type, continue?" By scott.n9 5 years ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Thank you! It makes no sense I need to tell it I h... 3 weeks ago By lupos So you will have to switch the profile in the slic... 12 months ago By Anach... Hi, I ran into the same issue and found this threa... 12 months ago By bitug... view all posts
	False Replace Filament Alarm By mike 3 months ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	this just happened to me in my last print(or two) ... 3 weeks ago By bapsk... I've seen this a couple times and never intentiona... 3 weeks ago By tonyP... You are correct. I accidentally added a filament ... 3 months ago By mike view all posts
	0.6mm HF nozzle first layer lines are too fine on textured sheet By Tgunn 7 months ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Here is my case which might or may not provide add... 3 weeks ago By 3DMas... @Tgunn I always clean the nozzle by doing the foll... 6 months ago By UjinD... I had similar problem. Now, I make sure to brush t... 6 months ago By strja... view all posts
	Core One ESP32-S3 Gcode Console/Progress Viewer By gb160 3 weeks ago \| Last Post: 3 weeks ago	User mods
	RE: Core One ESP32-S3 Gcode Console/Progress Viewer 3 weeks ago By gb160 This isn't so much as a mod, more of an addition r... 3 weeks ago By gb160
	Feature Request? Filament Color Indicator By Tony D 11 months ago \| Last Post: 3 weeks ago	Prusa Connect & PrusaLink
	How about the option to select a color at the prin... 3 weeks ago By Denni... Thank you to those of you who have replied. I wan... 11 months ago By Tony ... bearing in mind that there are many filament manuf... 11 months ago By JoanT... view all posts
	Hotend too long By DJetelina 3 weeks ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	Another part that seems to be oversized 3 weeks ago By DJete... Hi, I can’t seem to wrap my head around the main p... 3 weeks ago By DJete...
	Core One MMU - Next Gen Solution By iftibashir 4 months ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	The best spool / buffer solution for all MMU3 prin... 3 weeks ago By Disco... Even then - they still need a spool storage soluti... 3 weeks ago By iftib... Just fun speculation but I'm guessing maybe they c... 3 weeks ago By hyige... view all posts
	Power issues By 8bitHero 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I wish it was that simple. I did some troubleshoot... 3 weeks ago By 8bitH... In the second image, the main switch is in the 'Of... 3 weeks ago By miros... Either that or the power supply is faulty. If you ... 3 weeks ago By hyige... view all posts
	Extruder skipping By atlantis7 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Lately I experience a problem with a skipping extr... 3 weeks ago By atlan...