English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums Recent Posts Notifications Clear all Recent Posts Forums | Topics Recent Posts Unread Posts Not Replied Topics Solved Topics Unsolved Topics Closed Topics Open Topics Sticky Topics Page 44 / 44 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Topic Title Forum Z-Naht unschön By BastiRun 1 month ago | Last Post: 4 weeks ago Wie drucke ich das? (Hilfe zum Drucken) Die Projektdatei fehlt leider. Albernerweise erlau... 4 weeks ago By Jürge... Hallo allerseits, ich habe aktuell mal wieder sehr... 1 month ago By Basti... Seized Nuts foil Core ONE+ upgrade By cyrusjk 2 months ago | Last Post: 4 weeks ago Hardware, firmware and software help The square nuts and M3 screws provided by Prusa ar... 4 weeks ago By Augen... Yes, my suggestions were for the one-off situation... 2 months ago By Conra... Thanks for the tip, but galling is a hard stop; yo... 2 months ago By cyrus... view all posts Precision Homing Failed By Bob Keeney 1 month ago | Last Post: 4 weeks ago Hardware, firmware and software help After you have aligned the gantry and gotten the b... 4 weeks ago By Augen... Thanks. I actually figured it out a few hours aft... 1 month ago By Bob K... Since it's a kit, I'm assuming this is the Core On... 1 month ago By hyige... Sorry I have not posted lately. By John Lindo 4 weeks ago | Last Post: 4 weeks ago General discussion, announcements and releases I am back in the wagon again, had a few health iss... 4 weeks ago By John ... Prusa Slicer using multi beds centering your work By meathead 4 weeks ago | Last Post: 4 weeks ago PrusaSlicer The other shortcut specific to the new multi-bed o... 4 weeks ago By FoxRu... Are you using the "Z" shortcut? If so, try the "B"... 4 weeks ago By Semba... When using multiple beds four in my case I cant fi... 4 weeks ago By meath... Tilter/skewed belt? By abmantis 1 month ago | Last Post: 4 weeks ago Hardware, firmware and software help Yeah, maybe it has no impact. But the Core One alr... 4 weeks ago By abman... I wouldn't be too concerned about a quality impact... 4 weeks ago By Jürge... I can't say for sure, but it could cause VFAs (or ... 4 weeks ago By abman... view all posts Prusa Core One not usable inhouse... Sorry, but the sound was to intensiv By tomtim 11 months ago | Last Post: 4 weeks ago General discussion, announcements and releases Can you share a picture of the new motors? I got m... 4 weeks ago By abman... How? Mine peaks at 79dB on motor whine. 4 weeks ago By abman... I guess they fixed that problem, cause mine is pre... 1 month ago By NickA... view all posts Prusaslicer supports warning missing By langjai 4 weeks ago | Last Post: 4 weeks ago PrusaSlicer I found the settings in preferences and it is chec... 4 weeks ago By langj... I don't know if this is new in 2.9.4, but PS no lo... 4 weeks ago By langj... Prusa Connect Notification use Pause message By GBelfor 4 weeks ago | Last Post: 4 weeks ago Prusa Connect & PrusaLink I added a pause in my print to drop in magnets. B... 4 weeks ago By GBelf... New Purchases get INDX discount! By iftibashir 1 month ago | Last Post: 4 weeks ago General discussion, announcements and releases So true... 4 weeks ago By GBMar... Or you can think of it as giving an interest free ... 1 month ago By hyige... Yeah, no, they'll certainly ship it. It's more th... 1 month ago By GBMar... view all posts Error codes By mnentwig 4 weeks ago | Last Post: 4 weeks ago Signature Oak Probably a 99.9999% oxygen free copper mains cable... 4 weeks ago By hyige... let's stay clear of jigsaws or this might turn int... 4 weeks ago By mnent... Just follow the Signature Oak MMU upgrade guide, w... 4 weeks ago By Jürge... Print came loose and got trapped between bed and wall blocking Z axis movement. By NickAtNight 1 month ago | Last Post: 4 weeks ago Assembly and first prints troubleshooting I had a spaghetti print jam up the print bed and s... 4 weeks ago By hyige... Yes, PLA. The usual soap and warm water. What I a... 4 weeks ago By NickA... Well it happens. It always helps others to state w... 1 month ago By hyige... view all posts Linear bearings sound rattley (rattles) at front left of printer By J-Plasted 1 month ago | Last Post: 4 weeks ago Hardware, firmware and software help hey there, apologies for the late reply. i actuall... 4 weeks ago By J-Pla... Anyone else got a rattle coming from either the li... 1 month ago By J-Pla... Incomplete Printing By Scotttomo 1 month ago | Last Post: 4 weeks ago How do I print this? (Printing help) Cheers. Pretty sure it is, but will double check a... 4 weeks ago By Scott... Also make sure the outer toothed ring is installed... 4 weeks ago By hyige... Cheers for this. Washer is present and correct, al... 4 weeks ago By Scott... view all posts Reuse MMU3 from MK3S+ to CoreOne By Koos 4 months ago | Last Post: 4 weeks ago Hardware, firmware and software help Now I will wait for the INDX upgrade 😉 4 weeks ago By Koos I had contact with support. There is no official u... 4 months ago By Koos Contact support via chat to see if the MMU3 MK3.X ... 4 months ago By K7ZPJ Page 44 / 44 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Share:
