Recent Posts

Forums | Topics

Page 44 / 44 Prev

	Topic Title	Forum
	Prusa i3 MK3S+ 2023 printer firmware question. By OBI-WAN JACOBY 4 weeks ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	Hello, I recently assembled my MK3S+ kit and I jum... 4 weeks ago By OBI-W...
	Best nozzle for printing with glow in the dark PLA By A101 2 months ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	Glow-in-the-dark is not very abrasive so in my Mk3... 4 weeks ago By Diem I use ObXidian nozzles (non High Flow/CHT) from Pr... 4 weeks ago By Walte... A hardened steel standard nozzle should be good. I... 4 weeks ago By vhubb...
	TPU covered with white powder substance By Alex_D 1 month ago \| Last Post: 4 weeks ago	How do I print this? (Printing help)
	It does look odd and I've not seen it on Sunlu bef... 4 weeks ago By Diem Hello this is my first TPU: Sunlu 90A. It is cover... 1 month ago By Alex_...
	Z-Naht unschön By BastiRun 1 month ago \| Last Post: 4 weeks ago	Wie drucke ich das? (Hilfe zum Drucken)
	Die Projektdatei fehlt leider. Albernerweise erlau... 4 weeks ago By Jürge... Hallo allerseits, ich habe aktuell mal wieder sehr... 1 month ago By Basti...
	Seized Nuts foil Core ONE+ upgrade By cyrusjk 2 months ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	The square nuts and M3 screws provided by Prusa ar... 4 weeks ago By Augen... Yes, my suggestions were for the one-off situation... 2 months ago By Conra... Thanks for the tip, but galling is a hard stop; yo... 2 months ago By cyrus... view all posts
	Precision Homing Failed By Bob Keeney 1 month ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	After you have aligned the gantry and gotten the b... 4 weeks ago By Augen... Thanks. I actually figured it out a few hours aft... 1 month ago By Bob K... Since it's a kit, I'm assuming this is the Core On... 1 month ago By hyige...
	Sorry I have not posted lately. By John Lindo 4 weeks ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	I am back in the wagon again, had a few health iss... 4 weeks ago By John ...
	Prusa Slicer using multi beds centering your work By meathead 1 month ago \| Last Post: 4 weeks ago	PrusaSlicer
	The other shortcut specific to the new multi-bed o... 4 weeks ago By FoxRu... Are you using the "Z" shortcut? If so, try the "B"... 4 weeks ago By Semba... When using multiple beds four in my case I cant fi... 1 month ago By meath...
	Tilter/skewed belt? By abmantis 1 month ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	Yeah, maybe it has no impact. But the Core One alr... 4 weeks ago By abman... I wouldn't be too concerned about a quality impact... 4 weeks ago By Jürge... I can't say for sure, but it could cause VFAs (or ... 1 month ago By abman... view all posts
	Prusa Core One not usable inhouse... Sorry, but the sound was to intensiv By tomtim 11 months ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	Can you share a picture of the new motors? I got m... 4 weeks ago By abman... How? Mine peaks at 79dB on motor whine. 4 weeks ago By abman... I guess they fixed that problem, cause mine is pre... 1 month ago By NickA... view all posts