Recent Posts

Forums | Topics

Page 25 / 39 Prev Next

	Topic Title	Forum
	Audio? By David Holland 1 month ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	I was wondering the same, but when I tap into the ... 2 weeks ago By ductn... Hi, I guess two questions... 1) Does the Buddy3D ... 1 month ago By David...
	Advanced filtration system HEPA filter fan not turning. POWER light not on By samuel 8 months ago \| Last Post: 2 weeks ago	Prusa add-ons (GPIO, accelerometer,...)
	Did you figure out something here to make it work?... 2 weeks ago By Mijan Hello! I just installed the HEPA filter but the fa... 8 months ago By samue...
	Extrusion Multiplier Calibration By Pleny The Elder 3 weeks ago \| Last Post: 2 weeks ago	PrusaSlicer
	Did you also weight purge lines and supports? I wo... 2 weeks ago By _Kasz... I've been printing for about six months now and I ... 3 weeks ago By Pleny...
	Prusa connect - spojení tiskárny By vojtech.prostredni 2 weeks ago \| Last Post: 2 weeks ago	Hardware, firmware a software (Pomoc)
	Dobrý den, Nedaří se mi přidat moji nově postaveno... 2 weeks ago By vojte...
	Echec du test de chauffage buse By Pascalou 3 weeks ago \| Last Post: 2 weeks ago	Dépannage pour l'assemblage et les premières impressions
	Bonjour, Comme souvent, poser la question revient ... 2 weeks ago By Pasca... Bonjour, J'ai assemblé mon imprimante avec le pl... 3 weeks ago By Pasca...
	Inconsistent performance (flaws) By BigTim 3 months ago \| Last Post: 2 weeks ago	Hardware, firmware and software help
	Is there a way to set this as standard for all pri... 2 weeks ago By MileH... Try playing with Z-height. While printing press th... 3 months ago By strja... I have an MK4/S printer, the enclosure, and a dryi... 3 months ago By BigTi...
	Need help with first layer printing By Hodjone 2 weeks ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	I am trying to use my Prusa mini to printer a larg... 2 weeks ago By Hodjo...
	Core one problème nozzle clean , home Z et crash detection By Core Light 3 weeks ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	Cela fait plus d'1 ans que j'avais une MK4 qui a b... 3 weeks ago By Core ...
	Keine Filament-Auswahl nach Slicer-Update By RUDI 6 months ago \| Last Post: 3 weeks ago	Allgemeine Diskussion, Ankündigungen und Veröffentlichungen
	Warum kann man wenn man im Slicer auf mk3.5 MMU st... 3 weeks ago By Chris Vielen Dank Walter: Es hat geklappt. 😀 6 months ago By RUDI Im Konfigurations-Assistenten von PrusaSlicer kann... 6 months ago By Walte...
	Prusa XL 5 Head failing Z-Axis Test and Tool Offset Calibration By Scott MacDonald 2 years ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	Ha, brilliant! I found that I was able to tighten ... 3 weeks ago By JS I found it easier to mount the top frame while the... 3 weeks ago By ergo2... How do you "re-jig" it to get the vertical extrusi... 4 weeks ago By JS view all posts
	Prusa printer help By Ryan Willis 3 weeks ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	Hi I'm having problems with my Prusa printer and I... 3 weeks ago By Ryan ...
	Underextrusion with filament grinding By PotatoFi 4 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I'm about 5 prints in, and I've found that going o... 3 weeks ago By Potat... Recently I had temperature shooting to 300C in a s... 3 weeks ago By _Kasz... I may be on to something. On a whim, I bumped the ... 3 weeks ago By Potat... view all posts
	Y-Axis calibration is failing after several good prints By sassch 9 months ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	Ok calibration worked now. It worked fine before t... 3 weeks ago By sassc... Apologize for the late reply. No I checked everyth... 3 weeks ago By sassc... It sounds like your Y-axis might still have an iss... 6 months ago By Steve... view all posts
	prusaslicer linux compile By ice 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	I ran the install script on my Gentoo machine and ... 3 weeks ago By ice success! thanks for the help I also had to instal... 3 weeks ago By ice As my last build was on April 10 I ran a test buil... 3 weeks ago By Walte... view all posts
	MK3S+ sees all gcode models on card except for one model By RonM 3 weeks ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	I do not think uploading anything will help you. T... 3 weeks ago By RonM Slice the project as usual but save the project, (... 3 weeks ago By Diem Yep that was it. It wasn't the length but rather I... 3 weeks ago By RonM view all posts
	PP-CF bed temp and Nozzle discrepancies By JM 3 weeks ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	Ahhh... Apologies - I misinterpreted your prompt a... 3 weeks ago By JM Posted by: @david-r-campbell Settings ... I used... 3 weeks ago By JM Settings 3 weeks ago By David...
	Setting export for support By Pleny The Elder 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	A nice feature would be a simple export that would... 3 weeks ago By Pleny...
	Align Detraction/Retraction Points AND Seam By Tech Guy 3 years ago \| Last Post: 3 weeks ago	PrusaSlicer
	thanks for the .. language? lesson I guess anyway... 3 weeks ago By Vigil... It's not a workaround, It's the way. You should st... 3 weeks ago By Snuff... This was super helpful, I was looking for a settin... 3 weeks ago By Vigil... view all posts
	"Send to Connect" keyboard hotkey? By DanielRA 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	Hi all, Just out of curiosity, is there a reason w... 3 weeks ago By Danie...
	Unscheduled disassembly By Pierre-Yves 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Hello, I found this little grub screw on the buil... 3 weeks ago By Pierr...