Recent Posts

Forums | Topics

Page 4 / 38 Prev Next

	Topic Title	Forum
	WiFi and Ethernet not working By Akentut 8 months ago \| Last Post: 2 days ago	Hardware, firmware and software help
	No this was the WiFi interface circuit board, a ve... 2 days ago By Akent... Isn’t this the module for the camera? I need more... 1 month ago By BMC Problem solved! Replaced ESP32 module. 8 months ago By Akent... view all posts
	How do I automatically switch to a new filament roll when the filament roll runs out? By Richard3D 3 days ago \| Last Post: 2 days ago	PrusaSlicer
	Hi Richard, You have to do this on the printer. Wh... 2 days ago By Rufus How do I configure a Prusa slicer with an MMU3 to ... 3 days ago By Richa...
	Hello every one! By Fred Wilson 2 days ago \| Last Post: 2 days ago	General discussion, announcements and releases
	Hello every one.. i am new here! 2 days ago By Fred ...
	MMU3 Layer shift On core one 6.4.0-alpha By Alienbliep 2 weeks ago \| Last Post: 2 days ago	Hardware, firmware and software help
	Have you found an answer to this yet? I have also ... 2 days ago By Das-W... Hmm it is happening again. I think it is this blob... 2 weeks ago By Alien... Goodday, Today i had an massive layer shift ... 2 weeks ago By Alien...
	Can filament settings be changed per object? By Avinash 3 days ago \| Last Post: 2 days ago	PrusaSlicer
	Thanks for the tip. I am using TPU Air by Siraya T... 2 days ago By Avina... Alter the settings in the g code and insert M109 S... 2 days ago By John ... I have a filament that gives different textures at... 3 days ago By Avina...
	Y axis is mirrored By PEU 6 days ago \| Last Post: 2 days ago	Assembly and first prints troubleshooting
	I built three kits - testing revealed a mirrored m... 2 days ago By dawjr as expected, big FACEPALM... LMAO 5 days ago By PEU Its late here, will open the printer tomorrow, tha... 6 days ago By PEU view all posts
	LW-PLA By Josef Beck 5 months ago \| Last Post: 2 days ago	How do I print this? (Printing help)
	Hey, Buddy - LW-PLA can be confusing at first and ... 2 days ago By dawjr I would recommend printing slow speed 50mm per sec... 2 weeks ago By L3DCX... im folowing the topic any change? im also printing... 5 months ago By Induc... view all posts
	Missing PLA+ filament setting causes print issue? By stefs 2 days ago \| Last Post: 2 days ago	PrusaSlicer
	Hello experts! I can't find filament settings for ... 2 days ago By stefs
	Y-axis self test failing consistently By Filip Sádovský 2 years ago \| Last Post: 2 days ago	Assembly and first prints troubleshooting
	Well, I bought a new MK4S about a week ago, built ... 2 days ago By dando... Solved the dreaded 211 problem. Thank you. Thank y... 9 months ago By gsopp Mainly I was worried about a metal-to-metal end st... 9 months ago By Mechm... view all posts
	what is "Recommended thin wall thickness"? By how_to_prusa_slicer 3 days ago \| Last Post: 3 days ago	PrusaSlicer
	When they say the “thin wall thickness,” they are ... 3 days ago By Avina... hello, i'm trying to understand prusa slicer and i... 3 days ago By how_t...
	After each power on, new Core One recalibrates home, bangs the Nextruder against the corner and reports a printer collision By Matthias Nagel 6 days ago \| Last Post: 3 days ago	Assembly and first prints troubleshooting
	A reboot of the printer helped me out in this case... 3 days ago By KlinW... I am not sure to which cable you specifically refe... 4 days ago By Matth... I am not prusa support but I'd look at a couple of... 4 days ago By chmax view all posts
	PETG large print disaster By Hans 2 weeks ago \| Last Post: 3 days ago	How do I print this? (Printing help)
	Hi Tim Thanks for your reaction. I tried increasin... 3 days ago By Hans When clearing the stuck filament, don't be afraid ... 1 week ago By Tim Hi Diem Thanks for your answer. I will go with a d... 2 weeks ago By Hans view all posts
	Z Axis Test fails By dtice 2 years ago \| Last Post: 3 days ago	Hardware, firmware and software help
	I had a Z axis fail after re-calibration. I tried ... 3 days ago By Teddy... After talking with Prusa I decided to take the Z-A... 2 years ago By dtice I'm using the latest 5.1.2. I've narrowed the pro... 2 years ago By dtice view all posts
	Printing time uncerteinty By bielend 3 days ago \| Last Post: 3 days ago	How do I print this? (Printing help)
	I have a problem with printing time. There is very... 3 days ago By biele...
	MK4S + MMU3 problém. (Preheat problem/ termal runaway) I když tiskárna před upgradem fungovala By Vozitko 3 days ago \| Last Post: 3 days ago	Jak to vytisknu? (Pomoc s tiskem)
	Mám už skoro rok MK4S, funguje naprosto perfektně ... 3 days ago By Vozit...
	PID tuning caused thermal runaway with 6.4.0-alpha By hyiger 6 days ago \| Last Post: 3 days ago	General discussion, announcements and releases
	As a follow up, it seems one has to wait for the h... 3 days ago By hyige... M303 succeeded which is 150C default, tried M303 S... 6 days ago By hyige...
	Is Advanced Filtration supposed to smell weird By Lallu London 3 days ago \| Last Post: 3 days ago	General discussion, announcements and releases
	I have less than 100 hours using the Core One Adv.... 3 days ago By Lallu...
	What to do with samples and short ends? By efvee 11 months ago \| Last Post: 3 days ago	General discussion, announcements and releases
	Exactly, this is what I have used for over 1 year.... 3 days ago By John ... I throw them in the bin with skirts, supports, bri... 6 days ago By Green... This. I have printed a couple of Dingoboy71's Smal... 1 week ago By srmal... view all posts
	Saving filament changes across projects By Ninju 3 days ago \| Last Post: 3 days ago	PrusaSlicer
	Save the filament settings as a custom preset then... 3 days ago By Diem Hello fellow Prusaits (sp?), Is there any way t... 3 days ago By Ninju