Recent Posts

Forums | Topics

Page 8 / 36 Prev Next

	Topic Title	Forum
	filament not extruding properly By elif 1 week ago \| Last Post: 7 days ago	Assembly and first prints troubleshooting
	So it is definitely the idler tension screws but f... 7 days ago By elif Try slightly tightening (like an 1/8 of a turn), t... 7 days ago By hyige... i got a core one a few weeks ago and last week dur... 1 week ago By elif
	Filament remapping By langjai 7 days ago \| Last Post: 7 days ago	PrusaSlicer
	Please please please add this!!! 7 days ago By langj...
	Adding Printers By Rufus 7 days ago \| Last Post: 7 days ago	PrusaSlicer
	I finally figured this out. I am really sorry for ... 7 days ago By Rufus Thanks for the info Neophyl. I have to be doing so... 7 days ago By Rufus Ive just run the wizard again and Prusa seem to ha... 7 days ago By Neoph...
	Druk 3d By Natalia Brzozowska 1 week ago \| Last Post: 7 days ago	Dyskusja ogólna, ogłoszenia i wydania
	To zbyt ogólne pytanie. Drukowanie może trwać 5 mi... 7 days ago By Karko... Czy druk 3D na zamówienie jest szybki? Ile zwykle ... 1 week ago By Natal...
	WiFi and Ethernet not working By Akentut 8 months ago \| Last Post: 7 days ago	Hardware, firmware and software help
	No this was the WiFi interface circuit board, a ve... 7 days ago By Akent... Isn’t this the module for the camera? I need more... 2 months ago By BMC Problem solved! Replaced ESP32 module. 8 months ago By Akent... view all posts
	How do I automatically switch to a new filament roll when the filament roll runs out? By Richard3D 7 days ago \| Last Post: 7 days ago	PrusaSlicer
	Hi Richard, You have to do this on the printer. Wh... 7 days ago By Rufus How do I configure a Prusa slicer with an MMU3 to ... 7 days ago By Richa...
	Hello every one! By Fred Wilson 7 days ago \| Last Post: 7 days ago	General discussion, announcements and releases
	Hello every one.. i am new here! 7 days ago By Fred ...
	MMU3 Layer shift On core one 6.4.0-alpha By Alienbliep 3 weeks ago \| Last Post: 7 days ago	Hardware, firmware and software help
	Have you found an answer to this yet? I have also ... 7 days ago By Das-W... Hmm it is happening again. I think it is this blob... 3 weeks ago By Alien... Goodday, Today i had an massive layer shift ... 3 weeks ago By Alien...
	Can filament settings be changed per object? By Avinash 7 days ago \| Last Post: 7 days ago	PrusaSlicer
	Thanks for the tip. I am using TPU Air by Siraya T... 7 days ago By Avina... Alter the settings in the g code and insert M109 S... 7 days ago By John ... I have a filament that gives different textures at... 7 days ago By Avina...
	Y axis is mirrored By PEU 1 week ago \| Last Post: 7 days ago	Assembly and first prints troubleshooting
	I built three kits - testing revealed a mirrored m... 7 days ago By dawjr as expected, big FACEPALM... LMAO 1 week ago By PEU Its late here, will open the printer tomorrow, tha... 1 week ago By PEU view all posts
	LW-PLA By Josef Beck 5 months ago \| Last Post: 7 days ago	How do I print this? (Printing help)
	Hey, Buddy - LW-PLA can be confusing at first and ... 7 days ago By dawjr I would recommend printing slow speed 50mm per sec... 2 weeks ago By L3DCX... im folowing the topic any change? im also printing... 5 months ago By Induc... view all posts
	Missing PLA+ filament setting causes print issue? By stefs 7 days ago \| Last Post: 7 days ago	PrusaSlicer
	Hello experts! I can't find filament settings for ... 7 days ago By stefs
	Y-axis self test failing consistently By Filip Sádovský 2 years ago \| Last Post: 7 days ago	Assembly and first prints troubleshooting
	Well, I bought a new MK4S about a week ago, built ... 7 days ago By dando... Solved the dreaded 211 problem. Thank you. Thank y... 9 months ago By gsopp Mainly I was worried about a metal-to-metal end st... 9 months ago By Mechm... view all posts
	After each power on, new Core One recalibrates home, bangs the Nextruder against the corner and reports a printer collision By Matthias Nagel 2 weeks ago \| Last Post: 1 week ago	Assembly and first prints troubleshooting
	A reboot of the printer helped me out in this case... 1 week ago By KlinW... I am not sure to which cable you specifically refe... 1 week ago By Matth... I am not prusa support but I'd look at a couple of... 1 week ago By chmax view all posts
	PETG large print disaster By Hans 3 weeks ago \| Last Post: 1 week ago	How do I print this? (Printing help)
	Hi Tim Thanks for your reaction. I tried increasin... 1 week ago By Hans When clearing the stuck filament, don't be afraid ... 2 weeks ago By Tim Hi Diem Thanks for your answer. I will go with a d... 3 weeks ago By Hans view all posts
	Z Axis Test fails By dtice 2 years ago \| Last Post: 1 week ago	Hardware, firmware and software help
	I had a Z axis fail after re-calibration. I tried ... 1 week ago By Teddy... After talking with Prusa I decided to take the Z-A... 2 years ago By dtice I'm using the latest 5.1.2. I've narrowed the pro... 2 years ago By dtice view all posts
	Printing time uncerteinty By bielend 1 week ago \| Last Post: 1 week ago	How do I print this? (Printing help)
	I have a problem with printing time. There is very... 1 week ago By biele...
	MK4S + MMU3 problém. (Preheat problem/ termal runaway) I když tiskárna před upgradem fungovala By Vozitko 1 week ago \| Last Post: 1 week ago	Jak to vytisknu? (Pomoc s tiskem)
	Mám už skoro rok MK4S, funguje naprosto perfektně ... 1 week ago By Vozit...
	PID tuning caused thermal runaway with 6.4.0-alpha By hyiger 1 week ago \| Last Post: 1 week ago	General discussion, announcements and releases
	As a follow up, it seems one has to wait for the h... 1 week ago By hyige... M303 succeeded which is 150C default, tried M303 S... 1 week ago By hyige...
	Is Advanced Filtration supposed to smell weird By Lallu London 1 week ago \| Last Post: 1 week ago	General discussion, announcements and releases
	I have less than 100 hours using the Core One Adv.... 1 week ago By Lallu...