Recent Posts

Forums | Topics

Page 14 / 34 Prev Next

	Topic Title	Forum
	První spuštění tiskárny PROBLÉM MK4 By JamalXface3D 2 years ago \| Last Post: 2 weeks ago	Složení tiskárny a řešení potíží s prvním tiskem
	Tiskárna po zapnutí, kontroluje jednotlivé perifér... 2 weeks ago By pink_... Ahoj, mám stejný problém, sestavil jsem stavebnici... 9 months ago By mitta... Výška trysky (pokud je tím míněna hodnota osy Z) b... 10 months ago By Mion view all posts
	Hotend fan pulsing during pause despite nozzle being off By Franz Ament 2 weeks ago \| Last Post: 2 weeks ago	Hardware, firmware and software help
	exact the same here. (6.4 alpha and also on ear... 2 weeks ago By Ckoba... I've had this happen after a print finishes as wel... 2 weeks ago By hyige... Demonstrationvideo;Steps to reproduce: Print was p... 2 weeks ago By Franz...
	Špatné nastavení teploty trysky? By Lukáš Duběda 1 year ago \| Last Post: 2 weeks ago	Složení tiskárny a řešení potíží s prvním tiskem
	MK4 na rozdíl od mk3 nemá kompenzaci teploty pro t... 2 weeks ago By pink_... Jak by to asi řešil? Odpověď je o příspěvek výše. ... 7 months ago By miros... Jak jste to nakonec vyřešili? 7 months ago By Adriá... view all posts
	Printables - Copy/Paste bug? By shrap 4 weeks ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	Following Tampermonkey script works for me: // ==U... 2 weeks ago By cwohl... I can confirm this happens for me as well on firef... 2 weeks ago By cwohl... that checks out as to why I probably wasn't seeing... 2 weeks ago By Geoff... view all posts
	Migrating MMU3 from Mk3S+ to Core One? By Patronics 2 months ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	I have the same question 2 weeks ago By Koos I think it's finally time to bite the bullet and r... 2 months ago By Patro...
	filament dryer By skylab9999 2 weeks ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	Fillamentum doesn't agrees with those drying tempe... 2 weeks ago By Artur... Desiccant type dryers (like silica gel units): The... 2 weeks ago By skyla... I still have a question, where does the moisture g... 2 weeks ago By Green... view all posts
	Problem z selftestem osi X By pangus 2 weeks ago \| Last Post: 2 weeks ago	Hardware, firmware i oprogramowanie - pomoc
	Witam, przychodzę tutaj z problemem, który nie jes... 2 weeks ago By pangu...
	Manually adjust heat bed thermister calibration temp??? By Dazz 2 weeks ago \| Last Post: 2 weeks ago	Hardware, firmware and software help
	Hi I have replaced my heat bed thermister but now ... 2 weeks ago By Dazz
	Prusa Slicer settings for Anycubic Kobra S1 By Nolan 2 weeks ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	Was wondering if anyone had suggestions or config ... 2 weeks ago By Nolan
	Strange issues on prints By vsions 2 weeks ago \| Last Post: 2 weeks ago	Assembly and first prints troubleshooting
	It's a combination of extreme overhang and the dir... 2 weeks ago By Diem Hello, I have been trying to figure out why my pri... 2 weeks ago By vsion...
	Chronic Under-Extrusion - Core ONE By PaltrySun 2 weeks ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	Once you have consistently dry filament (and possi... 2 weeks ago By Diem Thanks for the responses! I only used PLA and P... 2 weeks ago By Paltr... clicking/grinding filament and stringy filament Ag... 2 weeks ago By Diem view all posts
	Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. By Dik Harrison 1 month ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	I am having the same issue! Hope there's an answer... 2 weeks ago By Crise... That is correct. Any suggestions? 3 weeks ago By Dik H... Buddy Camera that’s linked to a Core device (maybe... 4 weeks ago By Deepa...
	Large ABS + PLA print, PLA keeps clogging By xatlas0 4 weeks ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	I experienced a similar issue with the combo of AS... 2 weeks ago By dawso... What's the best way to check size and roundness so... 3 weeks ago By Diem The three most likely causes: - Out of spec filame... 4 weeks ago By xatla... view all posts
	Two head printing - Automatic switch By AAM Metaldyne 2 weeks ago \| Last Post: 2 weeks ago	How do I print this? (Printing help)
	You are looking for the Spooljoin function: Cheer... 2 weeks ago By Diem Hello, My compagny order a printer XL for indust... 2 weeks ago By AAM M...
	Core one firmware 6.4.0 alpha By Philippe BAUER 2 weeks ago \| Last Post: 2 weeks ago	Hardware, firmware and software help
	For the core one, concerning the phase stepping c... 2 weeks ago By Phili...
	Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App By Vincent5840 5 months ago \| Last Post: 2 weeks ago	Hardware, firmware and software help
	That's not entirely right. It may level the bed at... 2 weeks ago By CJD Thank you! 🙂 2 weeks ago By Timma... RE: Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App 2 weeks ago By Raine... view all posts
	MK4 Prusa Enclosure By Mullu 2 weeks ago \| Last Post: 2 weeks ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	danke für die schnelle Antwort. Ich bevorzuge die ... 2 weeks ago By Mullu Entweder den PTFE-Schlauch durch drücken von oben ... 2 weeks ago By Walte... Hallo, ich habe dieses Wochenende das Gehäuse für ... 2 weeks ago By Mullu
	CORE One: Funktion Türschalter? By M3T 2 weeks ago \| Last Post: 2 weeks ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Nach Kontakt mit Prusa des Rätsels Lösung: 1. Der ... 2 weeks ago By M3T Hallo, nach Inbetriebnahme des CORE One (Kalibrier... 2 weeks ago By M3T
	Strange issues on prints By vsions 2 weeks ago \| Last Post: 2 weeks ago	How do I print this? (Printing help)
	Hello, I have been trying to figure out why my pri... 2 weeks ago By vsion...