| |
Topic Title |
Forum |
 |
Changing layer height mid print By Wallace_Workshop 3 years ago | Last Post: 2 weeks ago
|
PrusaSlicer |
| |
|
 |
Homing takes a lot of time solution By AvariCe 4 months ago | Last Post: 2 weeks ago
|
Hardware, firmware and software help |
| |
|
|
|
Nevíte co s tím? By Jakub Křemen 2 years ago | Last Post: 2 weeks ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Confusion if printer is off when enqueueing prints... By Mk4User 2 weeks ago | Last Post: 2 weeks ago
|
General discussion & User Experience & Ideas |
| |
|
 |
Z axis trouble but only when printing By ghostrider13 8 months ago | Last Post: 2 weeks ago
|
Assembly and first prints troubleshooting |
| |
|
 |
erhabene Buchstaben ordentlich drucken By BastiRun 2 weeks ago | Last Post: 2 weeks ago
|
Grossartige Drucke & Tipps zum Drucken |
| |
|
 |
After each power on, new Core One recalibrates home, bangs the Nextruder against the corner and reports a printer collision By Matthias Nagel 1 month ago | Last Post: 2 weeks ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Core One "Ultimate Edition" By Jürgen 3 weeks ago | Last Post: 2 weeks ago
|
General discussion, announcements and releases |
| |
|
 |
Hardware updates library with release dates By Luigi Bernardi 2 weeks ago | Last Post: 2 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Failed to load config bundle error By Connor 2 weeks ago | Last Post: 2 weeks ago
|
General discussion, announcements and releases |
| |
|
 |
6.2.6 for the Original Prusa XL By Jan Kratochvíl 2 months ago | Last Post: 2 weeks ago
|
General discussion, announcements and releases |
| |
|
 |
Has any one setup a MotionEye server to feed to PrusaConnect? By Dik Harrison 6 months ago | Last Post: 2 weeks ago
|
General discussion & User Experience & Ideas |
| |
|
|
|
Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. By Dik Harrison 2 months ago | Last Post: 2 weeks ago
|
General discussion, announcements and releases |
| |
|
 |
Thermistor failure? By Eddie 2 weeks ago | Last Post: 2 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Extension Board - max LED Output Power By Kelevra-5137.5 2 weeks ago | Last Post: 2 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Supports. By John Lindo 2 weeks ago | Last Post: 2 weeks ago
|
General discussion, announcements and releases |
| |
|
 |
Core One Modified for Australia By hyiger 2 weeks ago | Last Post: 2 weeks ago
|
General discussion, announcements and releases |
| |
|
 |
Düsenreinigung Fail By niceneighbor 2 weeks ago | Last Post: 2 weeks ago
|
Hilfe zur Hardware, Firmware und Software |
| |
|
 |
The download queue is too long By Coviello 3 months ago | Last Post: 2 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Add PLA lubricant to my print? For noise. By shrap 2 weeks ago | Last Post: 2 weeks ago
|
How do I print this? (Printing help) |
| |
|