| |
Topic Title |
Forum |
 |
Printer troubleshooting (1 viewing) By Sonarcreature 4 weeks ago | Last Post: 1 min ago
|
General discussion, announcements and releases |
| |
|
 |
Discovering that PrusaSlicer settings for Prusa's own filaments are not always accurate By hyiger 1 month ago | Last Post: 5 mins ago
|
General discussion, announcements and releases |
| |
|
 |
Print Trouble shooting - Always second layer By SullySquatch 3 weeks ago | Last Post: 10 mins ago
|
General discussion, announcements and releases |
| |
|
 |
Where is the upgraded bed for Core One ? By Print_Fandango 2 weeks ago | Last Post: 12 mins ago
|
General discussion, announcements and releases |
| |
|
 |
Possible bug or error in Gcode ? (Layer shift) By Wuhan 6 days ago | Last Post: 15 mins ago
|
General discussion, announcements and releases |
| |
|
 |
Free Core One+ upgrade if purchased in past 60 days? By Mike 2 months ago | Last Post: 23 mins ago
|
General discussion, announcements and releases |
| |
|
 |
Possible ghosting issues after calibration By SocialMisanthrope 2 days ago | Last Post: 37 mins ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Poor Print Quality on Sloped Surfaces That Face the Rear By t5montecarlo 1 week ago | Last Post: 2 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Core One - Z osa By Killer85-Z 3 months ago | Last Post: 2 hours ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Failed First Print - Fix for PETG Benchy that shifted after a couple layers on textured sheet? By Stormy 1 week ago | Last Post: 2 hours ago
|
Prints troubleshooting |
| |
|
 |
Core One - tisk více filamenty By Kukačka 4 months ago | Last Post: 2 hours ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Why is the quality of my nylon-cf prints getting progressively worse? By samfo 2 days ago | Last Post: 2 hours ago
|
How do I print this? (Printing help) |
| |
|
 |
Core One - postřehy By Jedle2000 7 months ago | Last Post: 2 hours ago
|
Obecná diskuze, oznámení a novinky |
| |
|
|
|
rattling during printing By Bezbolestný Pekáč 2 weeks ago | Last Post: 2 hours ago
|
Prusa CORE One L |
| |
|
 |
prestane dávať filament By Jamal 2 days ago | Last Post: 2 hours ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
CORE ONE/ + / L By Jardoslav 4 weeks ago | Last Post: 3 hours ago
|
Obecná diskuze, oznámení a novinky |
| |
|
|
|
GCODE NENÍ PLNĚ KOMPATIBILNÍ By Skyro 3 hours ago | Last Post: 3 hours ago
|
Obecná diskuze, oznámení a novinky |
| |
|
|
|
Problém s osou Y By Skyro 3 weeks ago | Last Post: 3 hours ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Metallic Rattling while printing By Ducttapealien 4 weeks ago | Last Post: 3 hours ago
|
Hardware, firmware and software help |
| |
|
 |
Core One +: Auto Vent opening By Andhrimnir 4 days ago | Last Post: 3 hours ago
|
General discussion, announcements and releases |
| |
|