Recent Posts

Forums | Topics

Page 2 / 37 Prev Next

	Topic Title	Forum
	Large ABS + PLA print, PLA keeps clogging By xatlas0 2 weeks ago \| Last Post: 19 hours ago	General discussion, announcements and releases
	I experienced a similar issue with the combo of AS... 19 hours ago By dawso... What's the best way to check size and roundness so... 2 weeks ago By Diem The three most likely causes: - Out of spec filame... 2 weeks ago By xatla... view all posts
	Core One skipping steps/Layer shift By Enrique Specht 6 months ago \| Last Post: 19 hours ago	Hardware, firmware and software help
	I am having the exact same problem. The location o... 19 hours ago By Jane ... I seem to have the same, or at least similar probl... 7 days ago By Marti... I am experiencing the same issue, with a printable... 1 week ago By wdvc view all posts
	VFA still there after all "fixes" By Kenneth Li 19 hours ago \| Last Post: 19 hours ago	Hardware, firmware and software help
	Even after tensioning belts (i overtensioned both ... 19 hours ago By Kenne...
	Two head printing - Automatic switch By AAM Metaldyne 1 day ago \| Last Post: 19 hours ago	How do I print this? (Printing help)
	You are looking for the Spooljoin function: Cheer... 19 hours ago By Diem Hello, My compagny order a printer XL for indust... 1 day ago By AAM M...
	Core one firmware 6.4.0 alpha By Philippe BAUER 20 hours ago \| Last Post: 20 hours ago	Hardware, firmware and software help
	For the core one, concerning the phase stepping c... 20 hours ago By Phili...
	Düsentemperatur wird nicht angezeigt By [email protected] 1 day ago \| Last Post: 20 hours ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Heizt er den auf? Nicht, daß der Sensor in Ordnung... 20 hours ago By Digib... Hallo zusammen, ich habe heute meinen MK4, mehr od... 1 day ago By diete...
	Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App By Vincent5840 5 months ago \| Last Post: 20 hours ago	Hardware, firmware and software help
	That's not entirely right. It may level the bed at... 20 hours ago By CJD Thank you! 🙂 1 day ago By Timma... RE: Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App 1 day ago By Raine... view all posts
	MK4 Prusa Enclosure By Mullu 2 days ago \| Last Post: 20 hours ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	danke für die schnelle Antwort. Ich bevorzuge die ... 20 hours ago By Mullu Entweder den PTFE-Schlauch durch drücken von oben ... 2 days ago By Walte... Hallo, ich habe dieses Wochenende das Gehäuse für ... 2 days ago By Mullu
	Close to losing my mind By J 2 days ago \| Last Post: 20 hours ago	Assembly and first prints troubleshooting
	If you use manual controls does the print head mov... 20 hours ago By CJD Somehow, yes it does 2 days ago By J Can’t help but feel these’re something fundamental... 2 days ago By gb160 view all posts
	Nozzle temperature not correct By [email protected] 1 day ago \| Last Post: 20 hours ago	Assembly and first prints troubleshooting
	It's possible the thermistor in the heat block is ... 20 hours ago By hyige...
	CORE One: Funktion Türschalter? By M3T 5 days ago \| Last Post: 21 hours ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Nach Kontakt mit Prusa des Rätsels Lösung: 1. Der ... 21 hours ago By M3T Hallo, nach Inbetriebnahme des CORE One (Kalibrier... 5 days ago By M3T
	Strange issues on prints By vsions 21 hours ago \| Last Post: 21 hours ago	How do I print this? (Printing help)
	Hello, I have been trying to figure out why my pri... 21 hours ago By vsion...
	File Transfer Error When Using Prusa Connect By gurgleapps 2 years ago \| Last Post: 23 hours ago	Bugs & Errors
	I had this issue on my Mk3s+. Changing the sd card... 23 hours ago By Eliza... Hi, I had the same problem as every one with the e... 5 months ago By Victo... I also had transfer errors, but after formatting t... 8 months ago By Ender... view all posts
	MK4S Druckende Problem mit Extrusion By HannesH 1 day ago \| Last Post: 23 hours ago	Hardware, firmware and software help
	Ich habe noch etwas vergessen:1. MK4S Firmware Ver... 23 hours ago By Hanne... Hallo und Guten Tag! Ich habe mit meinem MK4S folg... 1 day ago By Hanne...
	Strange rattling noise By Jamie Porro 4 weeks ago \| Last Post: 23 hours ago	Hardware, firmware and software help
	I spent six weeks trying to get CoreOne to work pr... 23 hours ago By J.J. ... I did initially have a minor issue with the cable ... 3 weeks ago By Laura... view all posts
	Webcam App to instantly view Buddy camera livestream in Core One By dmast 2 months ago \| Last Post: 24 hours ago	General discussion, announcements and releases
	That must be it, thank you. From my iPhone, I was ... 24 hours ago By CW That might be the problem. Guest WiFi networks oft... 3 days ago By tbr @tbr-2 I can't get this to work and I don't know w... 4 days ago By CW view all posts
	High Flow Nozzle compatability By Wilko 10 months ago \| Last Post: 24 hours ago	Hardware, firmware and software help
	Hi Wilko, please what you mean by "profiles are al... 24 hours ago By Jendi... You can indeed choose a "regular" nozzel for the M... 10 months ago By Wilko The mk4s has profiles for standard and high flow n... 10 months ago By vhubb...
	6.4.0-RC Firmware for Prusa MK4S By Jan Kratochvíl 1 week ago \| Last Post: 24 hours ago	General discussion, announcements and releases
	I confirm that as of September 27, 2025, the error... 24 hours ago By Papyj... The bugs from Alpha are still present in this RC. 2 days ago By LarGr... SummaryNew featuresNozzle cleaning failed wizardFi... 1 week ago By Jan K...
	Printing with PC-CF, keeps lifting off print bed By Daniel Laszlo 2 months ago \| Last Post: 1 day ago	How do I print this? (Printing help)
	Same as @Daniel Laszlo, I was able to print some s... 1 day ago By hyige... I was able to get smaller parts to run with the IE... 1 day ago By Danie... Yep, I couldn't understand the negative reviews ei... 1 day ago By gb160 view all posts