| |
Titolo discussione |
Forum |
 |
nach neuinstallation von 3.14.1 startet der drucker nicht mehr Da atosvs 4 weeks fa | Ultimi post: 3 weeks fa
|
Hilfe zur Hardware, Firmware und Software |
| |
|
 |
Another Stuck Filament Post Da JOHNE 3 weeks fa | Ultimi post: 3 weeks fa
|
How do I print this? (Printing help) |
| |
|
 |
Prusaslicer - Prusa Connect Not working Da Balazscpt 1 year fa | Ultimi post: 3 weeks fa
|
PrusaSlicer |
| |
|
|
|
Button for "cancel all transfers" in a printer's Current Transfer list Da Kris 3 months fa | Ultimi post: 3 weeks fa
|
General discussion & User Experience & Ideas |
| |
|
|
|
viele umwege bis der druck beginnt.... wie kann ich dem abhelfen? Da hukunz 3 weeks fa | Ultimi post: 3 weeks fa
|
Hilfe zur Hardware, Firmware und Software |
| |
|
 |
Mini+ with Hardened Nozzle - Generic settings? Da KevS 3 weeks fa | Ultimi post: 3 weeks fa
|
User mods - OctoPrint, enclosures, nozzles, ... |
| |
|
 |
Maytag Dryer Knob (MK4S to the rescue!) Da HappyKatz 7 months fa | Ultimi post: 3 weeks fa
|
Awesome prints (Hall Of Fame) |
| |
|
 |
Prusa Slicer Legend deaktivieren Da Sascha321 3 weeks fa | Ultimi post: 3 weeks fa
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
| |
|
 |
Ideas for skew correction on a Core One Da hyiger 1 month fa | Ultimi post: 3 weeks fa
|
General discussion, announcements and releases |
| |
|
 |
Prusa CORE One Dry Box Da Scott 11 months fa | Ultimi post: 3 weeks fa
|
User mods |
| |
|
 |
Initiale Kalibrierung - Z Achse bewegt sich nicht Da NewMiraculix 3 weeks fa | Ultimi post: 3 weeks fa
|
Zusammenbau und Fehlersuche bei den ersten Druckversuchen |
| |
|
|
|
Fehler #17819 nach Firmwareupdate auf 6.4.0 Da Periz 2 months fa | Ultimi post: 3 weeks fa
|
Hilfe zur Hardware, Firmware und Software |
| |
|
|
|
Chyba teploty / thermal error Da Michal Kahovec 3 years fa | Ultimi post: 3 weeks fa
|
Hardware, firmware a software (Pomoc) |
| |
|
 |
PrusaLink with a Pi 2b+?? Da TheRedEyeBandit 3 weeks fa | Ultimi post: 3 weeks fa
|
General discussion & User Experience & Ideas |
| |
|
 |
problems with importing SVGs Da j-martin 3 weeks fa | Ultimi post: 3 weeks fa
|
PrusaSlicer |
| |
|
|
|
First Time Calibration - Z Level Error Da NewMiraculix 3 weeks fa | Ultimi post: 3 weeks fa
|
Assembly and first prints troubleshooting |
| |
|
|
|
Y-Achse Riemen spannen? Ich kapiere nicht wie? Da Dominic Ruetsch 1 month fa | Ultimi post: 3 weeks fa
|
Hilfe zur Hardware, Firmware und Software |
| |
|
 |
Only one belt vibrating (twice in a row) during manual belt tuning Da volcryn 1 month fa | Ultimi post: 3 weeks fa
|
Assembly and first prints troubleshooting |
| |
|
 |
Potential uneven heating of the bed. Da Nikola Grancharov 2 months fa | Ultimi post: 3 weeks fa
|
Prints troubleshooting |
| |
|
 |
Oddball Layer Shift on First Layer - Prusa Slicer / Core One Da GBMaryland 3 weeks fa | Ultimi post: 3 weeks fa
|
Hardware, firmware and software help |
| |
|