eSun ePA-CF, Carbon Fibre Slicer Profile.
 
Notifications
Clear all

eSun ePA-CF, Carbon Fibre Slicer Profile.  

Stránka 4 / 8
  RSS
jmone
(@jmone)
Reputable Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

I've a profile for non filled Zytel but I don't have a spool of either CF or GF Zytel

 

Napsal : 19/09/2020 3:01 am
edwardbarrowman se líbí
edwardbarrowman
(@edwardbarrowman)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@jmone

That should work, I believe the only difference for glass filed is the nozzle temp and bed temp which I'm familiar with. I have an MK3S

 

Napsal : 19/09/2020 6:09 am
jmone
(@jmone)
Reputable Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@edwardbarrowman I've attached my Zytel profile but you may want to pick out values rather than load it as I've a MK3S/MMU2, Mosquito Magnum Hot End, with a Tungsten Carbide nozzle.

 

Attachment removed
Napsal : 19/09/2020 9:18 pm
edwardbarrowman se líbí
edwardbarrowman
(@edwardbarrowman)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@jmone

I'm sorry I'm still new, pick out values? I have an MK3S and I'm using an olsson ruby, is that the .ini file that is attached? thank you!

Napsal : 20/09/2020 3:30 am
edwardbarrowman
(@edwardbarrowman)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@jmone

the file looks strange in txt it's all one straight line and doesn't look like other ini files inside? my email is [email protected] if you could possibly send me the direct .ini file, Thank you kindly!

This post was modified před 4 years by edwardbarrowman
Napsal : 20/09/2020 3:41 am
jmone
(@jmone)
Reputable Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

Hi Edward, the forum does not allow you to upload a INI file, so I just put .txt behind it.  Just remove the .txt so it says Zytel.ini.  I doubt this profile will work for your setup without changes, esp the temp as the Ruby nozzle has a lower thermal conductivity than my TC one (you will probably need to up the print temp, but you will need to experiment).  If you do load the INI directly then make sure to pick your MK3S not my MK3D/MMU2.  

Napsal : 21/09/2020 4:30 am
edwardbarrowman se líbí
edwardbarrowman
(@edwardbarrowman)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

Ok will do, but the link you put up just shows a "text screen" and is not downloadable, if you could send it to my email that would be much appreciated!!! thank you

Napsal : 21/09/2020 4:38 am
edwardbarrowman
(@edwardbarrowman)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@jmone

My email is ******************************* thank you!

Napsal : 21/09/2020 4:40 am
cwbullet
(@cwbullet)
Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

I would strongly recommend you ask a mod to remove your email from the forum post.  Spam engines are watching.   

--------------------
Chuck H
3D Printer Review Blog

Napsal : 21/09/2020 8:37 am
edwardbarrowman
(@edwardbarrowman)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@charles-h13

Thanks for the info

 

Napsal : 21/09/2020 8:59 am
3Delight
(@3delight)
Moderátor Moderator
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

Removed it for you Edward.

Napsal : 21/09/2020 11:25 am
edwardbarrowman se líbí
edwardbarrowman
(@edwardbarrowman)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@3delight

thank you!

Napsal : 21/09/2020 12:35 pm
jmone
(@jmone)
Reputable Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@edwardbarrowman - I've attached a Zip if that helps.

Attachment removed
Napsal : 22/09/2020 1:01 am
edwardbarrowman
(@edwardbarrowman)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@jmone

Thank you so much!

Napsal : 22/09/2020 6:42 am
marto
(@marto)
Eminent Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

@edwardbarrowman

Use Notepad +

Napsal : 03/10/2020 6:19 pm
Joeski
(@joeski)
Active Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

Hi folks, i've been getting these small lines on the walls like the photos below, any advice? I printed a test cube to see if it was anything obvious but it came out remarkably perfect. 

 

Napsal : 25/11/2020 8:10 am
Kenour
(@kenour)
Estimable Member
Topic starter answered:
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

On the cube there's internal corners to hide the layer change. I've been having this problem with CF. Selecting 'align' layer changes can help. But yeah, it's really prone to this.

Napsal : 25/11/2020 8:17 am
jmone
(@jmone)
Reputable Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

I've never seen anything likes this and I've gone through a few spools of CF now.  In Prusa Slicer (which I'm presuming you use), after it is sliced, check out the preview to see if this is in the sliced model itself.  

Napsal : 25/11/2020 9:24 am
Kenour
(@kenour)
Estimable Member
Topic starter answered:
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

Turn on retractions and un-retractions and have a look if they line up with the lines you see.

Napsal : 25/11/2020 10:06 am
Flo4Print
(@flo4print)
Noble Member
RE: eSun ePA-CF, Carbon Fibre Slicer Profile.

Strange , I don't have this behaviour with this filament. A lot of oozing like you yes. Could it be the the print over the oozing filament ?

MK3S & Fusion 360

Napsal : 25/11/2020 10:40 am
Stránka 4 / 8
Share: