Simplify3D with a Core 1+ Configuration?  

RE: Simplify3D with a Core 1+ Configuration?

And why are you asking here? Ask the developers on Github, developers don't come here for some incomprehensible reason.

RE: Simplify3D with a Core 1+ Configuration?

Posted by: @miroslav-h4

And why are you asking here? Ask the developers on Github, developers don't come here for some incomprehensible reason.

Simplify3D is not a Prusa product. Where on Github would you place such a request? It's not really addressed to the software development team but to product management I think.

Seems like the best place is Reddit, that tends to get Prusa's attention. (In contrast to their own user forum, annoyingly.) 

RE: Simplify3D with a Core 1+ Configuration?

Thanks @same-old-shane! I am withdrawing my comment that the forum is not getting Prusa's attention. Great to see the change! 👍 

RE: Simplify3D with a Core 1+ Configuration?

To (@same-old-shane)

Since we have an admin here, I would like to ask why the forum is so slow? Loading a page even with a slightly higher server load takes tens of seconds and usually ends with an Error 500 message and a picture of a disassembled printer. This is also the cause of multiple posts, which cannot be deleted even due to the small time limit! I won't fill this up with off topic posts, so admin, find a thread for answers and discussion on this topic.

RE: Simplify3D with a Core 1+ Configuration?

Posted by: @miroslav-h4

To (@same-old-shane)

Since we have an admin here, I would like to ask why the forum is so slow? Loading a page even with a slightly higher server load takes tens of seconds and usually ends with an Error 500 message and a picture of a disassembled printer. This is also the cause of multiple posts, which cannot be deleted even due to the small time limit! I won't fill this up with off topic posts, so admin, find a thread for answers and discussion on this topic.

This has been discussed at some length in the General section. Shane is working on it (or rather, working with the colleagues who need to work on it):
https://forum.prusa3d.com/forum/english-forum-general-discussion-announcements-and-releases/knock-knock-just-a-little-status-update-anyone-home/

RE: Simplify3D with a Core 1+ Configuration?

Thanks for the link.

RE: Simplify3D with a Core 1+ Configuration?

Posted by: @jurgen-7

Posted by: @miroslav-h4

To (@same-old-shane)

Since we have an admin here, I would like to ask why the forum is so slow? Loading a page even with a slightly higher server load takes tens of seconds and usually ends with an Error 500 message and a picture of a disassembled printer. This is also the cause of multiple posts, which cannot be deleted even due to the small time limit! I won't fill this up with off topic posts, so admin, find a thread for answers and discussion on this topic.

This has been discussed at some length in the General section. Shane is working on it (or rather, working with the colleagues who need to work on it):
https://forum.prusa3d.com/forum/english-forum-general-discussion-announcements-and-releases/knock-knock-just-a-little-status-update-anyone-home/

Possibly related, but a few other forums I use are getting absolutely hammered over the last few weeks with bots scraping content for LLM training.

RE: Simplify3D with a Core 1+ Configuration?

Because Prusa has, in the past, supplied the Configurations to other Prusa machines...just not the Core 1.

Posted by: @jurgen-7

Posted by: @miroslav-h4

And why are you asking here? Ask the developers on Github, developers don't come here for some incomprehensible reason.

Simplify3D is not a Prusa product. Where on Github would you place such a request? It's not really addressed to the software development team but to product management I think.

Seems like the best place is Reddit, that tends to get Prusa's attention. (In contrast to their own user forum, annoyingly.) 

RE: Simplify3D with a Core 1+ Configuration?

Posted by: @robert-hill

Because Prusa has, in the past, supplied the Configurations to other Prusa machines...just not the Core 1.

I understand the desire and request. Just wanted to say that there is no suitable addressee on Github for it. -- Anyway, Shane has already given the answer, although not a positive one. Seems that Prusa feels that the ball is in Simplify3D's court.  

RE: Simplify3D with a Core 1+ Configuration?

I am confused.  The Prusa Core One is specifically listed as a supported printer in the Simplify3D software.  The Core One "Plus" does not change anything other than top vent control and side spool, so I can't see that affecting any of the main features of the Simplify3D software?
Why can't you simply select Pruse Core One inside the Simplify3D configuration setup screen?   Will that not get you 99.5% of what you need?

Neal

RE: Simplify3D with a Core 1+ Configuration?

Here are the only Configurations for Prusa in Simplify3d that I see:

Posted by: @neal-2

I am confused.  The Prusa Core One is specifically listed as a supported printer in the Simplify3D software.  The Core One "Plus" does not change anything other than top vent control and side spool, so I can't see that affecting any of the main features of the Simplify3D software?
Why can't you simply select Pruse Core One inside the Simplify3D configuration setup screen?   Will that not get you 99.5% of what you need?

 

Neal