English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Page 5 / 190 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Next Topic Title Last Post Views Posts Author Low quality low layers (but not first layer) By Neophyl on Jan 06 2300 17 WashUDave First layer curling at edges causing print to ... By Nimartet on Jan 02 6955 6 Owen984 Bulge when print reaches "solid" lay... By fnhanks on Jan 01 395370 530 Nicolai FLEX filament TPE32 object shrinking By Jan on Dec 27 1973 1 Jan Elephant foot? Nozzle cleaning? By Eule on Dec 19 2333 7 Eule Fuzzy Skin - First Fuzzy Skin layers will not ... By Bart on Dec 19 2343 1 Bart Bad "lines" when print almost horizontal surfa... By Peter on Dec 19 2343 6 Peter ESUN PETG Print Settings Answered By Constantin on Dec 18 15151 32 Rocky79 Printing 250mm wide - A toolpath outside the p... By Brad on Dec 17 9499 13 PorrdigeFacto... What Settings Should I Be Looking At? By parallon on Dec 17 1830 7 parallon Can I print multiple colors at the same layer? By Tiago Carvalho on Dec 16 34134 19 0mib How do I print each layer in same infill direc... By ufanders on Dec 16 25919 21 Bvdv Moving the nozzle wipe By dflipse on Dec 15 7512 9 DrAl Flat spots/bad finish separation on supported ... By Evan Judson on Dec 13 1111 3 Evan Judson Gaps on top layer of print By Brian on Dec 13 1553 3 mgantner How to improve overhangs on this print? By Diem on Dec 12 2408 2 Maciej Latuse... Having cyclic underextrusion. Suspect bontech ... By RedDawg on Dec 09 1701 4 RedDawg how do i stop curling By Friedham on Dec 08 24405 25 Cowen Blob of filament extruded when resuming from a... By Daniel Siffred... on Dec 07 10088 13 RichardLarson Peeling off outlines By MaiBo on Dec 07 1476 2 MaiBo Page 5 / 190 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Next Share: