English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 184 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author PETG Infill and "Final" Layer Proble... Przez megan.s on Jun 15, 18 5620 5 WogerDog Dealing with steep curves and warping Przez joe.r9 on Jun 15, 18 2484 3 joe.r9 Help improving my prints much appreciated Przez josh.w3 on Jun 14, 18 2109 3 josh.w3 mk3 can't print abs on left side Przez mrmac on Jun 14, 18 1880 3 mrmac Does Prusa print its parts at 0.2mm layer heig... Przez Joe Prints on Jun 13, 18 2227 2 dimprov Gap in print when using pause and resume Przez Chuckaluphagus on Jun 13, 18 2484 1 Chuckaluphagu... problem with partly detached ledge inside cyli... Przez iainmalcolm1@g... on Jun 13, 18 2232 5 iainmalcolm1@... Newbie and first prints Przez Kai on Jun 13, 18 2868 15 bidibule PLA+ settings? Przez peter.c24 on Jun 13, 18 17432 3 BrentS How D I Print This? Przez Wingsy on Jun 11, 18 2296 4 Wingsy Anyone tried printing PETG onto PrintBite? Przez dimprov on Jun 08, 18 1763 2 dimprov Issue when using a raft Przez Fotoman on Jun 07, 18 3619 3 Fotoman Material for making a rolling pin ? Przez john.d36 on Jun 06, 18 2327 4 Aravon Dalpek Aero - Curling Overhangs Przez Zach on Jun 05, 18 2028 3 Zach T Rex 38 Hours Failed Print Przez Zach on Jun 04, 18 2239 3 Matthias Are These Fingers Too Small? Przez JoanTabb on Jun 04, 18 1796 4 Wingsy No issues untill recently and with certain pat... Przez JoanTabb on Jun 03, 18 747 2 screw_ball69 New and some help with prints Przez CMasso_G3D on Jun 03, 18 1779 5 CMasso_G3D Grouping a Hole Doesn't Cut It (Tinkercad) Przez JoanTabb on Jun 03, 18 6179 3 Wingsy Issues with first layers after support Przez josh.m4 on Jun 03, 18 4744 7 Roger Egli Strona 184 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: