English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Avisos Vaciar todo How do I print this? (Printing help) | RSS Página 184 / 190 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author PETG Infill and "Final" Layer Proble... Por megan.s on Jun 15, 18 5619 5 WogerDog Dealing with steep curves and warping Por joe.r9 on Jun 15, 18 2481 3 joe.r9 Help improving my prints much appreciated Por josh.w3 on Jun 14, 18 2107 3 josh.w3 mk3 can't print abs on left side Por mrmac on Jun 14, 18 1880 3 mrmac Does Prusa print its parts at 0.2mm layer heig... Por Joe Prints on Jun 13, 18 2224 2 dimprov Gap in print when using pause and resume Por Chuckaluphagus on Jun 13, 18 2483 1 Chuckaluphagu... problem with partly detached ledge inside cyli... Por iainmalcolm1@g... on Jun 13, 18 2232 5 iainmalcolm1@... Newbie and first prints Por Kai on Jun 13, 18 2867 15 bidibule PLA+ settings? Por peter.c24 on Jun 13, 18 17430 3 BrentS How D I Print This? Por Wingsy on Jun 11, 18 2292 4 Wingsy Anyone tried printing PETG onto PrintBite? Por dimprov on Jun 08, 18 1762 2 dimprov Issue when using a raft Por Fotoman on Jun 07, 18 3614 3 Fotoman Material for making a rolling pin ? Por john.d36 on Jun 06, 18 2327 4 Aravon Dalpek Aero - Curling Overhangs Por Zach on Jun 05, 18 2027 3 Zach T Rex 38 Hours Failed Print Por Zach on Jun 04, 18 2238 3 Matthias Are These Fingers Too Small? Por JoanTabb on Jun 04, 18 1792 4 Wingsy No issues untill recently and with certain pat... Por JoanTabb on Jun 03, 18 746 2 screw_ball69 New and some help with prints Por CMasso_G3D on Jun 03, 18 1776 5 CMasso_G3D Grouping a Hole Doesn't Cut It (Tinkercad) Por JoanTabb on Jun 03, 18 6173 3 Wingsy Issues with first layers after support Por josh.m4 on Jun 03, 18 4743 7 Roger Egli Página 184 / 190 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Siguiente Compartir: